APRILIA CAPONORD 1200 Скачать руководство пользователя страница 138

Страница: 138 / 439

•

If shorted to negative: disconnect the injector connector, set the key to ON and check if there

is a ground connection on the white/green cable: if there is connection, restore the cable

harness. If there is no connection, replace the injector.

•

If the circuit is open: check the connector on the component and the Marelli control unit

connector: if not OK, restore. If OK, check cable continuity between the ENGINE PIN 8 and

component PIN 2 and restore the cable harness.

External rear cylinder injector P0202

•

short circuit to positive/ short circuit to negative / open circuit

Error cause

•

If shorted to positive: excessive voltage has been detected at PIN 46. If shorted to negative:

no voltage has been detected. If the circuit is open: an interruption has been detected.

Troubleshooting

•

If shorted to positive: disconnect the injector connector, set key to ON, activate the compo-

nent with the diagnosis instrument and check the voltage on the orange/white cable on the

injector connector. If following the activation the voltage does not drop, restore the cabling,

otherwise replace the injector.

•

If shorted to negative: disconnect the injector connector, set the key to ON and check if there

is a ground connection on the orange/white cable: if there is connection, restore the cable

harness. If there is no connection, replace the injector.

•

If the circuit is open: check the connector on the component and the Marelli control unit

connector: if not OK, restore. If OK, check cable continuity between the ENGINE PIN 46 and

component PIN 2 and restore the cable harness.

Internal front cylinder injector P0205

•

short circuit to positive/ short circuit to negative / open circuit

Error cause

•

If shorted to positive: excessive voltage has been detected at PIN 53. If shorted to negative:

no voltage has been detected. If the circuit is open: an interruption has been detected.

Troubleshooting

•

If shorted to positive: disconnect the injector connector, set key to ON, activate the compo-

nent with the diagnosis instrument and check the voltage on the grey/red cable on the

injector connector. If following the activation the voltage does not drop, restore the cabling,

otherwise replace the injector.

•

If shorted to negative: disconnect the injector connector, set the key to ON and check if there

is a ground connection on the Grey/Red cable: if there is connection, restore the cable har-

ness. If there is no connection, replace the injector.

Electrical system

CAPONORD 1200

ELE SYS - 138

Содержание CAPONORD 1200
























































































































































































































































































































































































































































Результаты поиска

Содержание CAPONORD 1200

Отзывы:

Похожие инструкции для CAPONORD 1200

Бренды по названию

Популярные бренды

APRILIA CAPONORD 1200, Руководство по обслуживанию станции

Результаты поиска

Содержание CAPONORD 1200

Отзывы:

Похожие инструкции для CAPONORD 1200

Бренды по названию

Популярные бренды