APRILIA CAPONORD 1200 Скачать руководство пользователя страница 299

Страница: 299 / 439

Checking the front wheel

FRONT WHEEL BEARINGS

Carry out the check with the bearings fitted on the wheel.

CHECK THAT ALL PARTS ARE IN GOOD CONDITION, ESPECIALLY THOSE LISTED AS FOL-
LOWS.

ROTATION CHECK

•

Manually rotate the inside ring of each bearing. Rotation must be constant, smooth and

noiseless.

If one or both bearings do not fall within the control parameters:

•

Replace both wheel bearings.

RADIAL AND AXIAL CLEARANCE CHECK

•

Check the radial and axial clearance.

Axial clearance: a minimum axial clearance is allowed.

Radial clearance: none.

If one or both bearings do not fall within the control parameters:

•

Replace both wheel bearings.

ALWAYS REPLACE BOTH BEARINGS.
ALWAYS REPLACE THE BEARINGS WITH OTHERS OF THE SAME TYPE.

GASKETS

•

Check that the gaskets are in good conditions; replace them if they show signs of damage

or excessive wear.

ALWAYS REPLACE BOTH GASKETS.
ALWAYS REPLACE THE GASKETS WITH OTHERS OF THE SAME TYPE.

WHEEL AXLE

•

Use a dial gauge to check the wheel

axle eccentricity. Replace the wheel

axle if the eccentricity exceeds the limit

value.

Characteristic

Maximum eccentricity:

0.25 mm (0.0098 in)

CAPONORD 1200

Suspensions

SUSP - 299

Содержание CAPONORD 1200
























































































































































































































































































































































































































































Результаты поиска

Содержание CAPONORD 1200

Отзывы:

Похожие инструкции для CAPONORD 1200

Бренды по названию

Популярные бренды

APRILIA CAPONORD 1200, Руководство по обслуживанию станции

Результаты поиска

Содержание CAPONORD 1200

Отзывы:

Похожие инструкции для CAPONORD 1200

Бренды по названию

Популярные бренды