APRILIA CAPONORD 1200 Скачать руководство пользователя страница 177

Страница: 177 / 439

not met (speed and constant setup), it acts on the

preload until it reaches the ideal setup.

If the system has already reached the ideal posi-

tion, it will make no further adjustments.

Level in electrical circuit diagram:

VCU (Vehicle Control Unit) control unit

Location:

•

On the vehicle: under the saddle.

•

Connector: on the component.

Pin out:

1. Negative preloaded motor

2. Positive preloaded motor

3. Ground from VCU

4. Encoder 2

5. Supply from VCU

6. Encoder 1

DIAGNOSTICS INSTRUMENT: ADJUSTMENTS

Travel limits preloaded motor

•

When you replace the hydraulic press of the rear shock absorber preload, do the self-ac-

quisition of the end-of-travel positions.

•

Otherwise, if you replace the VCU control unit with a new from spare parts, the procedure

is automatically performed the first time the engine is switched ON.

DIAGNOSTICS INSTRUMENT: ELECTRICAL ERRORS

VCU ERRORS

Error preload motor Status Flag active C1619

Error cause

•

Overcurrent on the preload motor.

Troubleshooting

•

Check the connector on the component and the VCU connector. Disconnect the connector

of the component and check its insulation from ground and supply system of PIN 1 and 2;

also ensure that the two PINs are insulated between each other. If all the above-mentioned

tests have a positive outcome, replace the motor.

Error blocked preload motor C1620

Error cause

•

The motor does not run not even with routing of current greater than ~ 4 A.

Troubleshooting

CAPONORD 1200

Electrical system

ELE SYS - 177

Содержание CAPONORD 1200
























































































































































































































































































































































































































































Результаты поиска

Содержание CAPONORD 1200

Отзывы:

Похожие инструкции для CAPONORD 1200

Бренды по названию

Популярные бренды

APRILIA CAPONORD 1200, Руководство по обслуживанию станции

Результаты поиска

Содержание CAPONORD 1200

Отзывы:

Похожие инструкции для CAPONORD 1200

Бренды по названию

Популярные бренды