APRILIA CAPONORD 1200 Скачать руководство пользователя страница 169

Страница: 169 / 439

- 3rd gear: 50 - 100 km/h;

- 4th gear: 60 - 120 km/h;

- 5th gear: 65 - 160 km/h;

- 6th gear: 70 - 180 km/h.

Once the desired speed is reached, the system

may be activated (SET state) by pressing the

cruise control button briefly: the instrument panel

indicator lamp lights continuously to indicate that

the system is active. The throttle grip may now be

released, and the cruise control function will au-

tonomously maintain the selected speed.

During the run at cruising speed, it is possible to

use the accelerator to increase the speed up to a

maximum of 30 km/h without causing the system

to deactivate. By using again the accelerator, the

Cruise Control will be deactivated (back to ON sta-

tus, the warning light starts flashing again). The

speed control is deactivated (warning light starts

flashing) if:

- you accelerate until the cruising speed is excee-

ded by more than 30 km/h;

- the clutch is activated;

- one of the brake switches is activated;

- the vehicle speed goes out of the speed range

previously shown;

- the button ON/OFF Cruise is pressed briefly.

The system deactivates completely, the cruising

speed is reset, and the warning light goes off, if:

- the ON/OFF Cruise button is pressed for longer;

- the RUN/STOP switch is set to STOP;

- the key is set to OFF.

Level in electrical circuit diagram:

Pre-installations and accessories

Location:

•

On the vehicle: on the handlebar, right

hand side.

CAPONORD 1200

Electrical system

ELE SYS - 169

Содержание CAPONORD 1200
























































































































































































































































































































































































































































Результаты поиска

Содержание CAPONORD 1200

Отзывы:

Похожие инструкции для CAPONORD 1200

Бренды по названию

Популярные бренды

APRILIA CAPONORD 1200, Руководство по обслуживанию станции

Результаты поиска

Содержание CAPONORD 1200

Отзывы:

Похожие инструкции для CAPONORD 1200

Бренды по названию

Популярные бренды