APRILIA CAPONORD 1200 Скачать руководство пользователя страница 167

Страница: 167 / 439

•

short circuit to positive / open circuit, short circuit to negative

Error cause

•

If shorted to positive: an excessive voltage has been detected at PIN A5 EVC. If the circuit

is open, shorted to negative: a null voltage has been detected at PIN A5 EVC.

Troubleshooting

•

If shorted to positive: disconnect the connector of the component and check its insulation

from supply system of PIN 2; if the insulation is not present, restore the cabling, otherwise

replace the component.

•

If the circuit is open, shorted to negative: check the connector on the component and the

EVC connector. Disconnect the two connectors and check the continuity of the cable be-

tween PIN 2 potentiometer and PIN A5 EVC and restore the cable harness. If the cable

harness is not damaged check the insulation from ground of PIN 2 of the component: if the

insulation is not present, restore the cabling, otherwise replace the component.

CAPONORD 1200 TRAVEL PACK

VCU ERRORS

Error control output exhaust valve Status Flag active C1613

Error cause

•

Overcurrent on exhaust valve: the VCU goes in the recovery mode.

Troubleshooting

•

Check the connector on the component and the VCU connector. Disconnect the connector

of the component and check its insulation from ground and supply system of PIN 4 and 5;

also ensure that the two PINs are insulated between each other. If all the above-mentioned

tests have a positive outcome, replace the component.

Error control output exhaust valve shortcircuit C1614

Error cause

•

A shortcircuit on PIN L1 or on PIN L2 of the VCU connector has been detected.

Troubleshooting

•

Disconnect the connector of the valve and check its insulation from ground and supply sys-

tem of PIN 4 and 5: if the insulation is not present, restore the cabling, otherwise replace

the component.

Error control output exhaust valve open circuit C1615

Error cause

•

An interruption of the circuit has been detected.

Troubleshooting

•

Check the connector on the component and the VCU connector. Disconnect the two con-

nectors and check the continuity of the cable between the PIN 4 valve - PIN L1 VCU and

CAPONORD 1200

Electrical system

ELE SYS - 167

Содержание CAPONORD 1200
























































































































































































































































































































































































































































Результаты поиска

Содержание CAPONORD 1200

Отзывы:

Похожие инструкции для CAPONORD 1200

Бренды по названию

Популярные бренды

APRILIA CAPONORD 1200, Руководство по обслуживанию станции

Результаты поиска

Содержание CAPONORD 1200

Отзывы:

Похожие инструкции для CAPONORD 1200

Бренды по названию

Популярные бренды