APRILIA CAPONORD 1200 Скачать руководство пользователя

Страница: 120 / 439

•

If shorted to positive: excessive voltage has been detected at PIN 23 of the ENGINE con-

nector. If the circuit is open, shorted to negative: voltage equal to zero has been detected

at PIN 23 of the ENGINE connector

Troubleshooting

•

shorted to positive: check the value shown by the parameter of the white rear connector

Throttle Grip Position Sensor - track C: disconnect the connector and read the value indi-

cated by the diagnostics instrument: if the voltage does not vary, there is a short circuit in

the cable wiring; replace the throttle grip sensor if the voltage drops to zero.

•

if the circuit is open, shorted to negative: with open circuit, short it to negative: check the

throttle grip sensor connector and the Marelli control unit connector. If not OK, restore. If

OK, check circuit continuity between the two cable terminals. If not OK, restore; if OK, check

the cable ground insulation (from the throttle grip sensor connector or the control unit con-

nector): if the cable is not ground insulated, restore the wiring. If it is ground insulated, and

with the key set to ON, check that there is power supply for the potentiometer PIN A and

that PIN C is connected to ground. If both are correct, replace the throttle grip sensor; if not,

check the continuity of the cable that is not functioning properly: if there is continuity, replace

the control unit; if not, restore the wiring

White rear connector throttle grip position sensor - track D P0153

•

short circuit to positive / open circuit, short circuit to negative

Error cause

•

If shorted to positive: excessive voltage has been detected at PIN 11 of the ENGINE con-

nector. If the circuit is open, shorted to negative: voltage equal to zero has been detected

at PIN 11 of the ENGINE connector

Troubleshooting

•

shorted to positive: check the value shown by the parameter of the white rear connector

Throttle Grip Position Sensor - track D: disconnect the connector and read the value indi-

cated by the diagnostics instrument: if the voltage does not vary, there is a short circuit in

the cable wiring; replace the throttle grip sensor if the voltage drops to zero.

•

if the circuit is open, shorted to negative: check the throttle grip sensor connector and the

Marelli control unit connector. If not OK, restore. If OK, check circuit continuity between the

two cable terminals. If not OK, restore; if OK, check the cable ground insulation (from the

throttle grip sensor connector or the control unit connector): if the cable is not ground insu-

lated, restore the wiring. If it is ground insulated, and with the switch key set to ON, check

that there is power supply for the potentiometer PIN D and that PIN F is connected to ground.

If both are correct, replace the throttle grip sensor; if not, check the continuity of the cable

Electrical system

CAPONORD 1200

ELE SYS - 120

Содержание CAPONORD 1200
























































































































































































































































































































































































































































Результаты поиска

Содержание CAPONORD 1200

Отзывы:

Похожие инструкции для CAPONORD 1200

Бренды по названию

Популярные бренды

APRILIA CAPONORD 1200, Руководство по обслуживанию станции

Результаты поиска

Содержание CAPONORD 1200

Отзывы:

Похожие инструкции для CAPONORD 1200

Бренды по названию

Популярные бренды