APRILIA CAPONORD 1200 Скачать руководство пользователя страница 261

Страница: 261 / 439

pos.

Description

Type

Quantity

Torque

Notes

Camshaft retainer plate fastener

screw

torx M5

8.5 Nm (6.26 lbf ft)

3M SCOTCH GRIP

2353

Decompression device fixing screw

torx M8

28.5 Nm (21.02 lbf ft)

3M SCOTCH GRIP

2353

Fastener screw

5.50 Nm (4.06 lbf ft)

3M SCOTCH GRIP

2353

Installing the chain tensioner

Refit the removed timing system chain tensioner on the cylinder - head:

•

Fit the timing chain on the crankshaft and on the intermediate gear.

•

Remove the screw and collect the washer and the spring.

•

Fit the chain tensioner body on the cyl-

inder and insert a new paper gasket.

•

Tighten the two screws to the prescri-

bed torque.

•

Insert the spring and tighten the screw together with the washer.

Cam timing

Timing

•

Remove the flywheel.

•

Install the timing chains on the inter-

mediate gears.

•

Install special tool flange on flywheel

side crankcase and fasten it using the

two screws supplied.

Specific tooling

020720Y

Timing tool

CAPONORD 1200

Engine

ENG - 261

Содержание CAPONORD 1200
























































































































































































































































































































































































































































Результаты поиска

Содержание CAPONORD 1200

Отзывы:

Похожие инструкции для CAPONORD 1200

Бренды по названию

Популярные бренды

APRILIA CAPONORD 1200, Руководство по обслуживанию станции

Результаты поиска

Содержание CAPONORD 1200

Отзывы:

Похожие инструкции для CAPONORD 1200

Бренды по названию

Популярные бренды