APRILIA CAPONORD 1200 Скачать руководство пользователя страница 144

Страница: 144 / 439

•

If shorted to positive: excessive voltage has been detected at PIN 2 of the ENGINE con-

nector. If the circuit is open, shorted to negative: voltage equal to zero has been detected

at PIN 2 of the ENGINE connector.

Troubleshooting

•

If shorted to positive: disconnect the coil connector, set the key to ON, activate the coil with

the diagnostics instrument and check voltage at connector PIN 2: if there is voltage, restore

the cable harness; if voltage = 0, replace the coil.

•

If the circuit is open, shorted to negative: check electric characteristics of the coil: if not OK,

replace the coil, if OK check the coil connector and the Marelli control unit connector; if not

OK, restore, if OK, check cable continuity between the two cable terminals: if there is not

continuity, restore the cable harness; if there is cable continuity, with key set to ON, check

the ground insulation of the cable (from coil connector or control unit connector), if not OK,

restore cable harness.

Rear cylinder side coil P0354

•

shorted to positive / shorted to negative, open circuit.

Error cause

•

If shorted to positive: excessive voltage has been detected at PIN 1 of the ENGINE con-

nector. If the circuit is open, shorted to negative: voltage equal to zero has been detected

at PIN 1 of the ENGINE connector.

Troubleshooting

•

If shorted to positive: disconnect the coil connector, set the key to ON, activate the coil with

the diagnostics instrument and check voltage at connector PIN 1: if there is voltage, restore

the cable harness; if voltage = 0, replace the coil.

•

If the circuit is open, shorted to negative: check electric characteristics of the coil: if not OK,

replace the coil, if OK check the coil connector and the Marelli control unit connector; if not

OK, restore, if OK, check cable continuity between the two cable terminals: if there is not

continuity, restore the cable harness; if there is cable continuity, with key set to ON, check

the cable ground insulation (from coil connector or control unit connector), if not OK, restore

cable harness

Electrical system

CAPONORD 1200

ELE SYS - 144

Содержание CAPONORD 1200
























































































































































































































































































































































































































































Результаты поиска

Содержание CAPONORD 1200

Отзывы:

Похожие инструкции для CAPONORD 1200

Бренды по названию

Популярные бренды

APRILIA CAPONORD 1200, Руководство по обслуживанию станции

Результаты поиска

Содержание CAPONORD 1200

Отзывы:

Похожие инструкции для CAPONORD 1200

Бренды по названию

Популярные бренды