APRILIA CAPONORD 1200 Скачать руководство пользователя

Страница: 174 / 439

•

Disconnect the connector of the sensor and check its insulation from ground and supply

system of PIN 2: if the insulation is not present, restore the cabling, otherwise replace the

sensor.

Error temperature sensor open circuit C1410

Error cause

•

An interruption of the circuit has been detected.

Troubleshooting

•

Check the connector on the component and the VCU connector. Disconnect the two con-

nectors and check the continuity of the cable between PIN 2 sensor and PIN D1 VCU and

restore the cable harness. If the cable harness is not damaged, replace the sensor.

Rotary sensor

(IF APPLICABLE)

Function

Detect the position of the fork, that is the angle be-

tween the fork and the frame.

Operation / Operating principle

The system, by means of the VCU control unit

(Vehicle Control Unit), measures in real time the

energy transmitted to Caponord 1200 (damping of

the shock absorber) from the roughness of the

road surface and it adapts the calibration of the

suspension in real time in order to maximise com-

fort and keep the correct setup of the motorbike.

Level in electrical circuit diagram:

VCU (Vehicle Control Unit) control unit

Location:

•

On the vehicle: on the LH of the mo-

torbike, fastened to the frame.

•

Connector: on the component.

Electrical system

CAPONORD 1200

ELE SYS - 174

Содержание CAPONORD 1200
























































































































































































































































































































































































































































Результаты поиска

Содержание CAPONORD 1200

Отзывы:

Похожие инструкции для CAPONORD 1200

Бренды по названию

Популярные бренды

APRILIA CAPONORD 1200, Руководство по обслуживанию станции

Результаты поиска

Содержание CAPONORD 1200

Отзывы:

Похожие инструкции для CAPONORD 1200

Бренды по названию

Популярные бренды