APRILIA CAPONORD 1200 Скачать руководство пользователя страница 172

Страница: 172 / 439

•

A shortcircuit on PIN C2 or on PIN D2 of the VCU connector has been detected.

Troubleshooting

•

Check the insulation from ground and from supply system of the two cables of the button

(PIN C2 and PIN D2 VCU).

Error switch front brake open circuit C1506

Error cause

•

An interruption of the circuit has been detected.

Troubleshooting

•

Check the correct operation of the contacts of the button on its two positions and the con-

tinuity of the cables between the button connector and VCU connector (PIN C2 and PIN D2).

If the above-mentioned tests have a positive outcome, replace the button.

Error switch rear brake shortcircuit C1507

Error cause

•

A shortcircuit on PIN E2 or on PIN F2 of the VCU connector has been detected.

Troubleshooting

•

Check the insulation from ground and from supply system of the two cables of the button

(PIN E2 and PIN F2 VCU).

Error switch rear brake open circuit C1508

Error cause

•

An interruption of the circuit has been detected.

Troubleshooting

•

Check the correct operation of the contacts of the button on its two positions and the con-

tinuity of the cables between the button connector and VCU connector (PIN E2 and PIN F2).

If the above-mentioned tests have a positive outcome, replace the button.

Temperature and pressure sensor

(IF APPLICABLE)

Function

Detect the temperature and the diving/extension

speed of the fork.

Operation / Operating principle

The system, by means of the VCU control unit

(Vehicle Control Unit), measures in real time the

energy transmitted to Caponord 1200 (damping of

the shock absorber) from the roughness of the

Electrical system

CAPONORD 1200

ELE SYS - 172

Содержание CAPONORD 1200
























































































































































































































































































































































































































































Результаты поиска

Содержание CAPONORD 1200

Отзывы:

Похожие инструкции для CAPONORD 1200

Бренды по названию

Популярные бренды

APRILIA CAPONORD 1200, Руководство по обслуживанию станции

Результаты поиска

Содержание CAPONORD 1200

Отзывы:

Похожие инструкции для CAPONORD 1200

Бренды по названию

Популярные бренды