APRILIA CAPONORD 1200 Скачать руководство пользователя страница 191

Страница: 191 / 439

•

Check the pins 66 and 80 and the Vehicle connector of the Marelli control unit. If not OK,

restore. If OK, check pins 5 and 6 and the ABS control unit connector. If not OK, restore. If

OK, check overall operation of the Marelli control unit and ABS control unit: replace the

affected component if you find any fault.

DIAGNOSTICS INSTRUMENT: LOGIC ERRORS

CAN line towards ABS control unit U1711 - No signal/Configuration error

Error cause

•

If there is no signal, no signal is received from the ABS control unit. In case of configuration

error, some devices are present (e.g. ABS) that were not foreseen in the vehicle configura-

tion stored in the control unit.

Troubleshooting

•

Open the diagnosis tool devices status page to check if the control unit setting is actually

consistent with the motorcycle setting. Example: if the bike has an ABS system the correct

state that should be found in the diagnostics instrument device status screen will be: Aprilia

Traction Control present. In the event of a bike with ABS system present and indication of

the diagnostics instrument of: Aprilia Traction Control not present, update the control unit.

VCU ERRORS

Failed CAN reception from motor ECU C1300

Error cause

•

The VCU does not receive the signal from the motor control unit.

Troubleshooting

•

Check the continuity of the cable between PIN K2 VCU - PIN 66 VEHICLE motor control

unit and between PIN J2 VCU - PIN 80 VEHICLE motor control unit. The error is automat-

ically memorised when the communication between the two control units is restored. To exit

the diagnosis status and allow the VCU to resume operation in normal conditions, it is how-

ever necessary to switch from «OFF» to «ON».

Failed CAN reception from instrument panel C1301

Error cause

•

The VCU does not receive the signal from the instrument panel.

Troubleshooting

•

Check the continuity of the cable between the PIN K2 VCU - PIN 27 instrument panel (black

connector) and PIN J2 VCU - PIN 26 instrument panel (black connector). The error is au-

tomatically memorised when the communication between the two control units is restored.

To exit the diagnosis status and allow the VCU to resume operation in normal conditions, it

is however necessary to switch from «OFF» to «ON».

Failed CAN reception from ABS C1303

CAPONORD 1200

Electrical system

ELE SYS - 191

Содержание CAPONORD 1200
























































































































































































































































































































































































































































Результаты поиска

Содержание CAPONORD 1200

Отзывы:

Похожие инструкции для CAPONORD 1200

Бренды по названию

Популярные бренды

APRILIA CAPONORD 1200, Руководство по обслуживанию станции

Результаты поиска

Содержание CAPONORD 1200

Отзывы:

Похожие инструкции для CAPONORD 1200

Бренды по названию

Популярные бренды