APRILIA CAPONORD 1200 Скачать руководство пользователя страница 125

Страница: 125 / 439

connector PIN 3 is a few tenths of an Ohm; If it is above that value, restore cable harness.

Replace the sensor if it is correct.

rear cylinder air pressure sensor P0108

•

signal not valid.

Error cause

•

According to the engine operation data (rpm, throttle, etc.) an average value for the intake

pressure is estimated: if the value read deviates by a given percentage, this error is activa-

ted. The most frequent causes can be: abnormal resistance in the sensor circuit (for

example, rusted terminals) or sensor with poor performance.

Troubleshooting

•

Check the Marelli control unit connector and the sensor connector; if not OK, restore. If

everything is OK, check that resistance between ENGINE connector PIN 49 and sensor

connector PIN 3 is a few tenths of an Ohm; If it is above that value, restore cable harness.

Replace the sensor if it is correct.

Error for unexpected air intake in the front cylinder manifold P0210

•

signal not valid.

Error cause

•

A small difference between the estimated pressure and the measured pressure has been

detected: the measured pressure is higher than the estimated one (intake manifold condi-

tions).

Troubleshooting

•

Check the conditions of the intake manifold and cleanliness of the hole for pressure reading.

Error for unexpected air intake in the rear cylinder manifold P0211

•

signal not valid.

Error cause

•

A small difference between the estimated pressure and the measured pressure has been

detected: the measured pressure is higher than the estimated one (intake manifold condi-

tions).

Troubleshooting

•

Check the conditions of the intake manifold and cleanliness of the hole for pressure reading.

Estimation error for front cylinder intake manifold pressure P0215

•

too high pressure/too low pressure.

Error cause

CAPONORD 1200

Electrical system

ELE SYS - 125

Содержание CAPONORD 1200
























































































































































































































































































































































































































































Результаты поиска

Содержание CAPONORD 1200

Отзывы:

Похожие инструкции для CAPONORD 1200

Бренды по названию

Популярные бренды

APRILIA CAPONORD 1200, Руководство по обслуживанию станции

Результаты поиска

Содержание CAPONORD 1200

Отзывы:

Похожие инструкции для CAPONORD 1200

Бренды по названию

Популярные бренды