Agilent Technologies 2000 X-Series Скачать руководство пользователя страница 263

Страница: 263 / 352

Utility Settings

Agilent InfiniiVision 2000 X-Series Oscilloscopes User's Guide

263

•

— press this softkey to enter characters and move the cursor

to the previous character position.

•

Delete Character

— press the

softkeys until the desired

character is highlighted; then, press this softkey to delete the
character.

•

Use the

Clear

softkey to delete all annotation characters.

•

Press

to save the annotation edits.

Press the

Text Color

softkey and turn the Entry knob to select the

annotation color.

You can choose white, red, or colors that match analog channels, digital
channels, math waveforms, reference waveforms, or markers.

Press the

Background

softkey and turn the Entry knob to select the

annotation background:

•

Opaque

— the annotation has a solid background.

•

Inverted

— the annotation's foreground and background colors are

switched.

•

Transparent

— the annotation has a transparent background.

N O T E

You can use a connected USB keyboard instead of using the Spell (and other) character
editing softkeys.

Содержание 2000 X-Series

































































































































































































































































































































































Результаты поиска

Содержание 2000 X-Series

Отзывы:

Похожие инструкции для 2000 X-Series

Бренды по названию

Популярные бренды

Agilent Technologies 2000 X-Series, Руководство пользователя

Результаты поиска

Содержание 2000 X-Series

Отзывы:

Похожие инструкции для 2000 X-Series

Бренды по названию

Популярные бренды