Agilent Technologies 2000 X-Series Скачать руководство пользователя страница 114

Страница: 114 / 352

114

Agilent InfiniiVision 2000 X-Series Oscilloscopes User's Guide

Display Settings

To erase the results of previous acquisitions from the display, press the

Clear Persistence

softkey.

The oscilloscope will start to accumulate acquisitions again.

To return the oscilloscope to the normal display mode, turn off
persistence; then, press the

Clear Persistence

softkey.

Turning off persistence does not clear the display. The display is
cleared if you press the

Clear Display

softkey or if you press the

[AutoScale]

key (which also turns off persistence).

For another method of seeing worst- case extremes of varying waveforms,
see

"Glitch or Narrow Pulse Capture"

on page 161.

To clear the display

Press

[Display] > Clear Display

You can also configure the

[Quick Action]

key to clear the display. See

"Configuring the [Quick Action] Key"

on page 261.

To select the grid type

When the

Video

trigger type is selected (see

"Video Trigger"

on page 133),

and the vertical scaling of at least one displayed channel is 140 mV/div,
the

Grid

softkey lets you select from these grid types:

•

Full

— the normal oscilloscope grid.

•

— shows vertical grids, labeled on the left, from - 0.3 V to 0.8 V.

•

IRE

— (Institute of Radio Engineers) shows vertical grids in IRE units,

labeled on the left, from - 40 to 100 IRE. The 0.35 V and 0.7 V levels
from the

grid are also shown and labeled at the right. When the

IRE

grid is selected, cursor values are also shown in IRE units. (Cursor
values via the remote interface are not in IRE units.)

The

and

IRE

grid values are accurate (and match Y cursor values)

when the vertical scaling is 140 mV/division and the vertical offset is
245 mV.

To select the grid type:

Содержание 2000 X-Series

































































































































































































































































































































































Результаты поиска

Содержание 2000 X-Series

Отзывы:

Похожие инструкции для 2000 X-Series

Бренды по названию

Популярные бренды

Agilent Technologies 2000 X-Series, Руководство пользователя

Результаты поиска

Содержание 2000 X-Series

Отзывы:

Похожие инструкции для 2000 X-Series

Бренды по названию

Популярные бренды