manualshive.com logo in svg

Agilent Technologies 2000 X-Series, Руководство пользователя

Agilent Technologies 2000 X-Series - высокотехнологичный прибор для точных измерений. Подробное руководство пользователя доступно для бесплатного скачивания на manualshive.com. Эта инструкция поможет вам максимально эффективно использовать функционал прибора и достичь высоких результатов в вашей работе.

Поделиться
Скачать
background image

Triggers

10

Agilent InfiniiVision 2000 X-Series Oscilloscopes User's Guide

125

 

The trigger level for a selected digital channel is set using the threshold 
menu in the Digital Channel Menu. Press the 

[Digital]

 key on the front 

panel, then press the 

Thresholds

 softkey to set the threshold level (TTL, 

CMOS, ECL, or user defined) for the selected digital channel group. The 
threshold value is displayed in the upper- right corner of the display.

The line trigger level is not adjustable. This trigger is synchronized with 
the power line supplied to the oscilloscope.

Forcing a Trigger

The 

[Force Trigger]

 key causes a trigger (on anything) and displays the 

acquisition.

This key is useful in the Normal trigger mode where acquisitions are made 
only when the trigger condition is met. In this mode, if no triggers are 
occurring (that is, the "Trig'd?" indicator is displayed), you can press 

[Force 

Trigger]

 to force a trigger and see what the input signals look like.

In the Auto trigger mode, when the trigger condition is not met, triggers 
are forced and the "Auto?" indicator is displayed.

Edge Trigger

The Edge trigger type identifies a trigger by looking for a specified edge 
(slope) and voltage level on a waveform. You can define the trigger source 
and slope in this menu. The trigger type, source, and level (if applicable) 
are displayed in the upper- right corner of the display.

1

On the front panel, in the Trigger section, press the 

[Trigger]

 key.

2

In the Trigger Menu, press the 

Trigger

 softkey, and use the Entry knob 

to select 

Edge

.

3

Select the trigger source:

•

Analog channel, 

1

 to the number of channels

N O T E

You can also change the trigger level of all channels by pressing [Analyze] > Features and 
then selecting Trigger Levels.

Содержание 2000 X-Series

































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2000 X-Series

Datavideo DN-100 Operation Manual preview
DN-100
Бренд: Datavideo Страницы: 28
R&S RTC1000 User Manual preview
RTC1000
Бренд: R&S Страницы: 371
R.M. Young 06206 Instructions Manual preview
06206
Бренд: R.M. Young Страницы: 9
Qlight S180U Manual preview
S180U
Бренд: Qlight Страницы: 4
Zimmer GED5000IL Series Installation And Operating Instructions Manual preview
GED5000IL Series
Бренд: Zimmer Страницы: 52
Oase LUNAQUA Classic LED Operating Instructions Manual preview
LUNAQUA Classic LED
Бренд: Oase Страницы: 16
gartenpirat Spielturm Premium L GP1122 Assembly Instruction Manual preview
Spielturm Premium L GP1122
Бренд: gartenpirat Страницы: 8
gartenpirat Lisa-Fun GP1604 Assembly Instructions Manual preview
Lisa-Fun GP1604
Бренд: gartenpirat Страницы: 6
Kanlux TEAR N Manual preview
TEAR N
Бренд: Kanlux Страницы: 4
Aspect Medical Systems BIS VIEW Operating Manual preview
BIS VIEW
Бренд: Aspect Medical Systems Страницы: 104
Hupfer BTH/60-60 Operating Instructions Manual preview
BTH/60-60
Бренд: Hupfer Страницы: 153
Ivoclar Vivadent Programat CS3 Operating Instructions Manual preview
Programat CS3
Бренд: Ivoclar Vivadent Страницы: 92
NBCUniversal LIGHTBLADE LB800 User Manual preview
LIGHTBLADE LB800
Бренд: NBCUniversal Страницы: 15
LIGMAN LIGHT LINEAR PT 1 Installation Manual preview
LIGHT LINEAR PT 1
Бренд: LIGMAN Страницы: 6
QRS 83529 MIDI Instructions Manual preview
83529 MIDI
Бренд: QRS Страницы: 12
Ikan Oryon Quick Start Manual preview
Oryon
Бренд: Ikan Страницы: 5
ADJ ikon profile ww User Instructions preview
ikon profile ww
Бренд: ADJ Страницы: 15
Fuso Multi Use Tester III Instruction Manual preview
Multi Use Tester III
Бренд: Fuso Страницы: 92

Бренды по названию

Популярные бренды

Загрузить еще бренды