manualshive.com logo in svg

Agilent Technologies 2000 X-Series, Руководство пользователя

Поделиться
Скачать
Agilent Technologies 2000 X-Series Скачать руководство пользователя страница 320

320

Agilent InfiniiVision 2000 X-Series Oscilloscopes User's Guide

24

I2C/SPI Triggering and Serial Decode

 

If don't care (0xXX) is selected for data, the data will be ignored. 
The trigger will always occur on the 17th clock for 7- bit addressing 
or 26th clock for 10- bit addressing.

c

If you have selected a three- byte trigger, press the 

Data2

 value softkey 

and turn the Entry knob to select the 8- bit data pattern on which to 
trigger.

I2C Serial Decode

To set up the oscilloscope to capture I2C signals, see 

"Setup for I2C 

Signals"

on page 315.

To set up I2C serial decode:

1

Press 

[Serial]

 to display the Serial Decode Menu.

2

Choose 7- bit or 8- bit address size. Use 8- bit address size to include the 
R/W bit as part of the address value, or choose 7- bit address size to 
exclude the R/W bit from the address value.

3

If  the  decode  line  does  not  appear  on  the  display,  press  the 

[Serial]

 key 

to turn it on.

4

If the oscilloscope is stopped, press the 

[Run/Stop]

 key to acquire and 

decode data.

N O T E

To display I2C serial decode, see 

"I2C Serial Decode"

on page 320.

N O T E

For I2C triggering setup see 

"I2C Triggering"

on page 316.

Содержание 2000 X-Series

































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды