manualshive.com logo in svg

Agilent Technologies 2000 X-Series, Руководство пользователя

Поделиться
Скачать
Agilent Technologies 2000 X-Series Скачать руководство пользователя страница 172

172

Agilent InfiniiVision 2000 X-Series Oscilloscopes User's Guide

13

Cursors

 

•

Press the 

Cursors

 softkey; then, turn the Entry knob.

The 

X1 X2 linked

 and 

Y1 Y2 linked

 selections let you adjust both cursors at 

the same time, while the delta value remains the same. This can be 
useful, for example, for checking pulse width variations in a pulse train.

The currently selected cursor(s) display brighter than the other cursors.

6

To change the cursor units, press the 

Units

 softkey.

In the Cursor Units Menu:

You can press the 

X Units

 softkey to select:

•

Seconds (s)

.

•

Hz (1/s)

.

•

Phase (°)

 — when selected, use the 

Use X Cursors

 softkey to set the 

current X1 location as 0 degrees and the current X2 location as 360 
degrees.

•

Ratio (%)

 — when selected, use the 

Use X Cursors

 softkey to set the 

current X1 location as 0% and the current X2 location as 100%.

You can press the 

Y Units

 softkey to select:

•

Base

 — the same units used for the source waveform.

•

Ratio (%)

 — when selected, use the Use 

Y Cursors

 softkey to set the 

current Y1 location as 0% and the current Y2 location as 100%.

For phase or ratio units, once the 0 and 360 degree or 0 and 100% 
locations are set, adjusting cursors will display measurements relative 
to the set locations.

7

Adjust the selected cursor(s) by turning the Cursors knob.

Содержание 2000 X-Series

































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды