Agilent Technologies 2000 X-Series Скачать руководство пользователя страница 302

Страница: 302 / 352

302

Agilent InfiniiVision 2000 X-Series Oscilloscopes User's Guide

CAN/LIN Triggering and Serial Decode

•

Remote Frame ID (RTR)

— The oscilloscope triggers on remote frames

with the specified ID. Press the

Bits

softkey to select the ID.

•

Data Frame ID (~RTR)

— The oscilloscope will trigger on data frames

matching the specified ID. Press the

Bits

softkey to select the ID.

•

Remote or Data Frame ID

— The oscilloscope will trigger on remote or

data frames matching the specified ID. Press the

Bits

softkey to select

the ID.

•

Data Frame ID and Data

— The oscilloscope will trigger on data frames

matching the specified ID and data. Press the

Bits

softkey to select

the ID and set up the number of data bytes and values.

•

Error Frame

— The oscilloscope will trigger on CAN active error frames.

•

All Errors

— The oscilloscope will trigger when any form error or

active error is encountered.

•

Acknowledge Error

— The oscilloscope will trigger when the

acknowledge bit is recessive (high).

•

Overload Frame

— The oscilloscope will trigger on CAN overload

frames.

If you select a condition that lets you trigger on ID or data values, use
the

Bits

softkey and the CAN Bits Menu to specify those values.

For details about using the CAN Bits Menu softkeys, press and hold the
softkey in question to display the built- in help.

You can use the

Zoom

mode for easier navigation of the decoded data.

N O T E

If the setup does not produce a stable trigger, the CAN signal may be slow enough that the
oscilloscope is AutoTriggering. Press the [Mode/Coupling] key, then press the Mode
softkey to set the trigger mode from Auto to Normal.

N O T E

To display CAN serial decode, see

"CAN Serial Decode"

on page 303.

Содержание 2000 X-Series

































































































































































































































































































































































Результаты поиска

Содержание 2000 X-Series

Отзывы:

Похожие инструкции для 2000 X-Series

Бренды по названию

Популярные бренды

Agilent Technologies 2000 X-Series, Руководство пользователя

Результаты поиска

Содержание 2000 X-Series

Отзывы:

Похожие инструкции для 2000 X-Series

Бренды по названию

Популярные бренды