manualshive.com logo in svg

Agilent Technologies 2000 X-Series, Руководство пользователя

Поделиться
Скачать
Agilent Technologies 2000 X-Series Скачать руководство пользователя страница 62

62

Agilent InfiniiVision 2000 X-Series Oscilloscopes User's Guide

3

Vertical Controls

 

1

Press the desired channel key.

2

In the Channel Menu, press the 

Coupling

 softkey to select the input 

channel coupling:

•

DC

 — DC coupling is useful for viewing waveforms as low as 0 Hz 

that do not have large DC offsets.

•

AC

  —  AC  coupling  is  useful  for  viewing  waveforms  with  large  DC 

offsets.

AC coupling places a 10 Hz high- pass filter in series with the input 
waveform that removes any DC offset voltage from the waveform.

Note that Channel Coupling is independent of Trigger Coupling. To change 
trigger coupling see 

"To select the trigger coupling"

on page 148.

To specify bandwidth limiting

1

Press the desired channel key.

2

In the Channel Menu, press the 

BW Limit

 softkey to enable or disable 

bandwidth limiting.

When bandwidth limit is on, the maximum bandwidth for the channel is 
approximately 20 MHz. For waveforms with frequencies below this, turning 
bandwidth limit on removes unwanted high frequency noise from the 
waveform. The bandwidth limit also limits the trigger signal path of any 
channel that has 

BW Limit

 turned on.

To change the vertical scale knob's coarse/fine adjustment setting

1

Push the channel's vertical scale knob (or press the channel key and 
then the 

Fine

 softkey in the Channel Menu) to toggle between fine and 

coarse adjustment of the vertical scale.

T I P

If the channel is DC coupled, you can quickly measure the DC component of the signal by 
simply noting its distance from the ground symbol.

If the channel is AC coupled, the DC component of the signal is removed, allowing you to 
use greater sensitivity to display the AC component of the signal.

Содержание 2000 X-Series

































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды