Agilent Technologies 2000 X-Series Скачать руководство пользователя страница 231 | Manualshive

Страница: 231 / 352

Agilent Technologies 2000 X-Series Скачать руководство пользователя страница 231

Save/Recall (Setups, Screens, Data)

18

Agilent InfiniiVision 2000 X-Series Oscilloscopes User's Guide

231

•

Setup Info

— when enabled, setup information (vertical, horizontal,

trigger, acquisition, math, and display settings) is also saved in a
separate file with a TXT extension.

•

Length

— sets the number of data points that will be output to the

file. For more information, see

"Length Control"

on page 231.

•

Save Seg

— when data is acquired to segmented memory, you can

specify whether the currently displayed segment is saved or all
acquired segments are saved. (See also

"Saving Data from Segmented

Memory"

on page 168.)

4

Finally, press the

Press to Save

softkey.

A message indicating whether the save was successful is displayed.

See Also

•

"Binary Data (.bin) Format"

on page 289

•

"CSV and ASCII XY files"

on page 296

•

"Minimum and Maximum Values in CSV Files"

on page 297

Length Control

The

Length

control is available when saving data to CSV, ASCII XY, or BIN

format files. It sets the number of data points that will be output to the
file. Only displayed data points are saved.

The maximum number of data points depends on these things:

•

Whether acquisitions are running. When stopped, data comes from the
raw acquisition record. When running, data comes from the smaller
measurement record.

•

Whether the oscilloscope was stopped using

[Stop]

or

[Single]

. Running

acquisitions split memory to provide fast waveform update rates. Single
acquisitions use full memory.

•

Whether only one channel of a pair is turned on. (Channels 1 and 2 are
one pair, channels 3 and 4 are the other.) Acquisition memory is
divided among the channels in a pair.

•

Whether reference waveforms are on. Displayed reference waveforms
consume acquisition memory.

•

Whether digital channels are on. Displayed digital channels consume
acquisition memory.

•

Whether segmented memory is on. Acquisition memory is divided by
the number of segments.

«
...
229
230
231
232
233
...
»

Содержание 2000 X-Series

































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды