ActionTec V2000H Скачать руководство пользователя страница 84 | Manualshive

Страница: 84 / 130

background image

Page 84 of 130

Figure 90: Steps for configuring wireless extender

3.

Press the WPS button on the side panel of the Extender for more than 8 seconds. Once you release
the button, it will start flashing with a red ring.

4.

Within 2 minutes of performing step 3, press the WPS button the front of the gateway for two
seconds. It will start flashing.

Note - Actiontec V1000H WPS button flashes green and red; V2000H flashes green only

5.

Wait for the process to complete. If the pairing is successful, the WPS button on the Extender will be
illuminated with a green ring.

Note - If unsuccessful, the WPS button on the Extender will continue to flash with a red ring for two minutes
then it will be illuminated with a red ring. If this occurs, unplug the devices from each other and perform this
procedure again.

If the two above methods fail, the Wireless network extender can be configured by logging into the
extender’s GUI. Using this method the WCB3000N Wireless Network Extender is powered up and connected
to a gateway via Ethernet cable, allowing the device to receive a dynamically assigned IP address from the
gateway. Using this IP address, the technician will then be able to access the Extender’s GUI.

«
...
82
83
84
85
86
...
»

Содержание V2000H



































































































































Отзывы:

Нет отзывов

Похожие инструкции для V2000H

Бренд: Xsense Connectivity Страницы: 56

Бренд: MachPower Страницы: 26

Бренд: Zks Страницы: 20

Бренд: Linksys Страницы: 69

Бренд: Linksys Страницы: 140

Бренд: ZyXEL Communications Страницы: 164

Бренд: Air Live Страницы: 160

Бренд: EnGenius Страницы: 2

Бренд: EnGenius Страницы: 64

Бренд: EnGenius Страницы: 46

Бренд: TSC Страницы: 19

Бренд: Solwise Страницы: 37

Air Premier DAP-2695

Бренд: D-Link Страницы: 40

Бренд: H3C Страницы: 21

NanoBeam NBE2ACN

Бренд: Ubiquiti Страницы: 28

Бренд: Abocom Страницы: 2

Бренд: Lanpro Страницы: 16

Бренд: Eaton Страницы: 25

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды