ActionTec V2000H Скачать руководство пользователя

Страница: 122 / 130

Page 122 of 130



Terminal information can be looked up using the COID & the Access Point number



This query will provide the Terminal address along with the counts.



This query also shows binding post information for each range.

Figure 133: AP inquiry

Cable Pair Inquiry – Cable Capacity Tab



This tab gives information on a range of cable pairs within a CO with relevant capacity totals for that
range.



This includes the percentage of pairs used, damaged, and available.



Enter the COID, the cable number, start and end pair for the range, and province.

Figure 134: Cable Pair Enquiry



In addition detailed information for each pair in the specified range is also shown, including the
address and line equipment attached to that pair.

Figure 135: Spare Pair Information

Line Equipment Inquiry – LE & SE Tab



By entering the COID, line equipment and switch unit number, you can obtain the location, status,
and attached TN, if applicable, of the requested Line Equipment.

Содержание V2000H



































































































































Результаты поиска

Содержание V2000H

Отзывы:

Похожие инструкции для V2000H

Бренды по названию

Популярные бренды

ActionTec V2000H, Руководство пользователя

Результаты поиска

Содержание V2000H

Отзывы:

Похожие инструкции для V2000H

Бренды по названию

Популярные бренды