manualshive.com logo in svg

ZyXEL Communications EX3510-B1, User Manual

Share
Download
ZyXEL Communications EX3510-B1 User Manual Download Page 245

EX3510-B1 User’s Guide

245

C

HAPTER

 29

Remote Management

29.1  Remote Management Overview

Use remote management to control what services you can use through which interface(s) in order to 
manage the Zyxel Device.

29.1.1  What You Can Do in this Chapter

• Use the 

MGMT Services

 screen to allow various approaches to access the Zyxel Device remotely from 

a WAN and/or LAN connection (

Section 29.2 on page 245

).

• Use the 

Trust Domain

 screen to enable users to permit access from local management services by 

entering specific IP addresses (

Section 29.3 on page 247

).

Note: The Zyxel Device is managed using the Web Configurator.

29.2  MGMT Services

Use this screen to configure through which interface(s), each service can access the Zyxel Device. You 
can also specify service port numbers computers must use to connect to the Zyxel Device. Click 

Maintenance

 > 

Remote Management

 > 

MGMT Services

 to open the following screen.

Summary of Contents for EX3510-B1


























































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands