manualshive.com logo in svg

ZyXEL Communications EX3510-B1, User Manual

Share
Download
ZyXEL Communications EX3510-B1 User Manual Download Page 20

Chapter 1 Introducing the Zyxel Device

EX3510-B1 User’s Guide

20

Figure 5   

LED Indicators

None of the LEDs are on if the Zyxel Device is not receiving power.

Table 2   LED Descriptions

LED

COLOR

STATUS

DESCRIPTION

POWER

Green

On

The Zyxel Device is receiving power and ready for use.

Blinking

The Zyxel Device is booting.

Red

On

The Zyxel Device detected an error while self-testing, or there is a device 
malfunction.

Blinking

The Zyxel Device is upgrading firmware.

Off

The Zyxel Device is not receiving power.

INTERNET

Green

On

The Zyxel Device has an IP connection but no traffic.

Your device has a WAN IP address (either static or assigned by a DHCP 
server), PPP negotiation was successfully completed (if used).

Blinking

The Zyxel Device is sending or receiving IP traffic.

Off

There is no Internet connection or the gateway is in bridged mode.

Red

On

The Zyxel Device attempted to make an IP connection but failed. Possible 
causes are no response from a DHCP server, no PPPoE response, PPPoE 
authentication failed.

Summary of Contents for EX3510-B1


























































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands