Home
/
YASKAWA
/
MP2100 Series
/
User Manual

YASKAWA MP2100 Series, User Manual

Share

Page: 214 / 455

background image

8.2 Positioning (POSING)

8-5

8

8.2 Positioning (POSING)

The POSING command positions the axis to the target position using the specified target position and speed.
Parameters related to acceleration and deceleration are set in advance.
The speed and target position can be changed during operation. When the target position is changed so that there
is not sufficient deceleration distance or after the new target position has already been passed, the system will
first decelerate to a stop and then reposition according to the new target position.

(1) Operating Procedure

* If the Position Reference Type (OB

095) is set for an absolute mode, the target position can be set

before executing the command.

(2) Holding

Axis travel can be stopped during command execution and then the remaining travel can be restarted. A com-
mand is held by setting the Command Pause bit (OB

090) to 1.

1. Set the Command Pause bit (OB

090) to 1. The axis will decelerate to a stop. When the axis has

stopped, the Hold Completed bit (IB

091) will turn ON.

2. Reset the Command Pause bit (OB

090) to 0. The command hold status will be cleared and the remain-

ing portion of the positioning will be restarted.

No.

Execution Conditions

Confirmation Method

1

There are no alarms.

Both IL

02 and IL

04 are 0.

2

The Servo ON condition.

IB

001 is ON.

3

Motion command execution has been completed.

IW

08 is 0 and IB

090 is OFF.

Set the motion setting parameters.

• Positioning Speed: OL

10

• Acceleration/Deceleration Filter Type:

OW

03

• Speed Loop P/PI Switch: OW

01

• The target position can be changed while the axis is moving.
• The positioning speed can be changed while the axis is moving.
• An override of between 0% to 327.67% can be set for the position-

ing speed.

• Set OB

090 to 1 to hold the command.

• Set OB

091 to 1 or execute the NOP motion command to abort

the command.

Execute the positioning (POSING) motion
command.

• Set OW

08 to 1.

Set the target position.

• Target Position Setting: OL

1C

∗

Positioning starts.

• IW

08 will be 1 during positioning.

Position proximity reached.

• IB

0C3 will turn ON.

Positioning completed.

• IB

0C1 will turn ON.

Executed NOP motion command.

• Set OW

08 to 0.

Position
reference

Speed

%

100%

0

Time

t

Positioning
speed

Linear

acceleration time

Linear

deceleration time

Rated speed

«
...
212
213
214
215
216
...
»

Summary of Contents for MP2100 Series








































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MP2100 Series

Brand: Microchip Technology Pages: 37

Brand: Gardena Pages: 14

Brand: Gardena Pages: 4

GAT ACCESS 6100

Brand: Gantner Pages: 4

Brand: LAS Pages: 6

Brand: olympia electronics Pages: 10

Brand: Omnex Pages: 9

Brand: Omegon Pages: 6

Brand: WATERLOO Pages: 8

Compact Comfort VAV12

Brand: SAI HVAC Pages: 16

Brand: Saitek Pages: 15

Brand: saia-burgess Pages: 203

Brand: Sailor Pages: 1

Brand: Rabbit Pages: 12

Brand: National Instruments Pages: 4

Brand: CALEFFI Pages: 10

EZ-ZONE PM L AAAAB Series

Brand: Watlow Pages: 30

Brand: Vageo Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands