manualshive.com logo in svg

YASKAWA MOTOMAN FS100, Maintenance Manual

The YASKAWA MOTOMAN FS100 is a state-of-the-art robotic system designed to optimize industrial manufacturing processes. Enhance your productivity by downloading the comprehensive Instructions Manual for this product, available for free download exclusively at our website.

Share
Download
background image

9-174

1596

45-1

C

D

RE-CHO-A1

11

FS10

0

8

The 1st-axis (elevation axis) 
positions of C3, C4, and C5 of 
station axes are not the same.

Setting error

(1)Check the following settings.
·Perform the teaching again so that the 1staxis (elevation axis) positions of C3, 
C4, and C5 of station axes are the same.

4498

CANNOT EXECUTE JOB
(NO GRP AXIS)

An attempt was made to execute 
an instruction that could not be 
executed in a job without control 
group.

Setting error

(1)Check the following settings.
·Check the settings for the job instruction with control group.

4499

UNDEFINED POSITION 
VARIABLE

Sub Code: The variable number

Setting error

(1)Check the following settings.
·Check the settings for the position type variable.

4500

UNDEFINED USER 
FRAME

Sub Code: User coordinate 
number

Setting error

(1)Check the following settings.
·Check the settings for the user coordinate.

4501

OUT OF RANGE 
(PARALLEL PROCESS)

Sub Code: Task number

Software operation error 
occurred

(1)Reset the alarm, and then try again.
(2)If the alarm occurs again, save the CMOS.BIN in maintenance mode, and 
then contact your YASKAWA representative about occurrence status (operating 
procedure).

4502

SL BOARD ON-LINE 
ERROR

The option board was detected 
not to operate normally at power 
ON.

Software operation error 
occurred

(1)Reset the alarm, and then try again.
(2)If the alarm occurs again, save the CMOS.BIN in maintenance mode, and 
then contact your YASKAWA representative about occurrence status (operating 
procedure).

4507

REFP POS ERROR   
(SEARCH MOTION)

Setting error

(1)Check the following settings.
·Perform the teaching again so that the search start point and the motion target 
point are not the same.
·Increase the distance between the search start point and the motion target 
point.

4508

SPECIFIED ERROR 
(COORDINATE)

0

The specified coordinate system 
does not exist.

Setting error

(1)Check the following settings.
·Check the settings for the coordinate system which can be used.

1

Designation error of the master 
tool coordinate system. This 
coordinate system cannot be 
used.

Setting error

(1)Check the following settings.
·Check the settings for the coordinate system which can be used.

2

Designation error of the tool 
coordinate system.  This 
coordinate system cannot be 
used.

Setting error

(1)Check the following settings.
·Check the settings for the coordinate system which can be used.

Alarm
Number

Alarm Name

Sub
Code

Meaning

Cause

Remedy

276 of 348

Summary of Contents for MOTOMAN FS100





























































































































































































































































































































































Reviews:

No comments

Related manuals for MOTOMAN FS100

ABB HF Series Manual preview
HF Series
Brand: ABB Pages: 63
Abicor Binzel EWR Quick Install Instructions preview
EWR
Brand: Abicor Binzel Pages: 8
Samson 3277 Mounting And Operating Instructions preview
3277
Brand: Samson Pages: 48
jbc DDE-1B Manual preview
DDE-1B
Brand: jbc Pages: 44
jbc SKR Instruction Manual preview
SKR
Brand: jbc Pages: 8
Madas M16/RMO NA/NC Installation Instructions Manual preview
M16/RMO NA/NC
Brand: Madas Pages: 6
Madas EVP/NC Manual preview
EVP/NC
Brand: Madas Pages: 11
R82 Cricket User Guidance preview
Cricket
Brand: R82 Pages: 89
Viking VC-1000 Technical Practice preview
VC-1000
Brand: Viking Pages: 4
Vag GA Figure 220-D Installation, Operation And Maintenance Manual preview
GA Figure 220-D
Brand: Vag Pages: 6
Rain Bird EASY RAIN Manual preview
EASY RAIN
Brand: Rain Bird Pages: 11
4EVAC LOOPDRIVE FIM-RC Quick Start Manual preview
LOOPDRIVE FIM-RC
Brand: 4EVAC Pages: 2
Simpnic IRB-01-SW Quick Installation Manual preview
IRB-01-SW
Brand: Simpnic Pages: 16
KAR-TECH CAN RANGER Operation Manual preview
CAN RANGER
Brand: KAR-TECH Pages: 55
Go Power 10 AMP RVC-MPPT User Manual preview
10 AMP RVC-MPPT
Brand: Go Power Pages: 17
Watts Industries PR500 Instruction Manual preview
PR500
Brand: Watts Industries Pages: 20
Acard PCI-to-IDE ATA-133 User Manual preview
PCI-to-IDE ATA-133
Brand: Acard Pages: 33
Hall Research Technologies VSA-51 User Manual preview
VSA-51
Brand: Hall Research Technologies Pages: 47

Brands by name

Popular brands

Load more brands