manualshive.com logo in svg

YASKAWA MOTOMAN FS100, Maintenance Manual

The YASKAWA MOTOMAN FS100 is a state-of-the-art robotic system designed to optimize industrial manufacturing processes. Enhance your productivity by downloading the comprehensive Instructions Manual for this product, available for free download exclusively at our website.

Share
Download
background image

9-55

15964

5-1CD

RE-CHO-A1

11

FS
10

0

1308

CONVERTER TYPE 
MISMATCH

Sub Code: Signifies the converter 
in which the alarm occurred

Setting error

(1)Check the following settings.
·Check the current capacity of the amplifier before/after replacement by the 
model described in board.
·When the external axis is mounted, check if there is no difference between the 
amplifier selected at configuration and practically mounted one.
Reference parameter: from SVCxB025

Connection failure

(1)Turn the power OFF then back ON.
(2)If the alarm occurs again, replace controller. Save the CMOS.BIN before 
replace controller to be safe.

Module failure (converter)

(1)Turn the power OFF then back ON.
(2)If the alarm occurs again, replace controller. Save the CMOS.BIN before 
replace controller to be safe.

Servo control board failure

(1)Turn the power OFF then back ON.
(2)If the alarm occurs again, replace controller. Save the CMOS.BIN before 
replace controller to be safe.

Software operation error 
occurred

(1)Turn the power OFF then back ON.
(2)If the alarm occurs again, save the CMOS.BIN in maintenance mode, and 
then contact your YASKAWA representative about occurrence status (operating 
procedure).

1311

A/D DETECTION 
ERROR (CONVERTER)

Sub Code: Signifies the converter 
physical number in which the 
alarm occurred

Module failure (converter)

(1)Turn the power OFF then back ON.
(2)If the alarm occurs again, replace controller. Save the CMOS.BIN before 
replace controller to be safe.

1325

COMMUNICATION 
ERROR (ENCODER)

Sub Code: Signifies the axis in 
which the alarm occurred

Connection failure

(1)Turn the power OFF then back ON.
(2)If the alarm occurs again, check the connecting or inserting state of the 
following cables.
{Robot axis}
·Cables between the controller and the encoder.
{External axis}
·Cables between the controller and the encoder.

Module failure (encoder)

(1)Turn the power OFF then back ON.
(2)If the alarm occurs again, replace the encoder.

Servo control board failure

(1)Turn the power OFF then back ON.
(2)If the alarm occurs again, replace controller. Save the CMOS.BIN before 
replace controller to be safe.

Alarm
Number

Alarm Name

Sub
Code

Meaning

Cause

Remedy

157 of 348

Summary of Contents for MOTOMAN FS100





























































































































































































































































































































































Reviews:

No comments

Related manuals for MOTOMAN FS100

ZIMO MX10 Instruction Manual preview
MX10
Brand: ZIMO Pages: 38
Badger Basket 9960 Assembly Instructions preview
9960
Brand: Badger Basket Pages: 3
BADLANDS LE-03 Quick Manual preview
LE-03
Brand: BADLANDS Pages: 2
Rain Bird ESP-LXD Installation, Programming & Operation Manual preview
ESP-LXD
Brand: Rain Bird Pages: 138
GI.BI.DI AS05582 Installation Instructions Manual preview
AS05582
Brand: GI.BI.DI Pages: 60
Tormatic DuoControl Signal 111 Quick Start Manual preview
DuoControl Signal 111
Brand: Tormatic Pages: 3
Valco baby ZEE Product Reference Manual preview
ZEE
Brand: Valco baby Pages: 8
baby joy TS10030 Quick Start Manual preview
TS10030
Brand: baby joy Pages: 11
jbc HDE-9UD Instruction Manual preview
HDE-9UD
Brand: jbc Pages: 16
Qorvo QM33120WDK1 Quick Start Manual preview
QM33120WDK1
Brand: Qorvo Pages: 6
OmarLift HEVOS HE650 Operating Instructions Manual preview
HEVOS HE650
Brand: OmarLift Pages: 50
M-system R7ML-EC16A Instruction Manual preview
R7ML-EC16A
Brand: M-system Pages: 3
Mamas & Papas 03 Sport Manual preview
03 Sport
Brand: Mamas & Papas Pages: 28
IEI Technology SPXE-14S-R20 Quick Installation Manual preview
SPXE-14S-R20
Brand: IEI Technology Pages: 6
JBL Six Button Remote User Manual preview
Six Button Remote
Brand: JBL Pages: 5
A-T Controls Triad Controls WE Series Installation And Operation Manual preview
Triad Controls WE Series
Brand: A-T Controls Pages: 13
Satel CA16128P Installer Manual preview
CA16128P
Brand: Satel Pages: 40
Texas Instruments TDP0604 User Manual preview
TDP0604
Brand: Texas Instruments Pages: 19

Brands by name

Popular brands

Load more brands