YASKAWA MOTOMAN FS100 Maintenance Manual Download Page 150 | Manualshive

Page: 150 / 348

background image

9-48

1596

45-1

C

D

RE-CHO-A1

11

FS10

0

1007

The check item number of SVC
parameter is unmatched.

Software operation error
occurred

(1)Turn the power OFF then back ON.
(2)If the alarm occurs again, save the CMOS.BIN in maintenance mode, and
then contact your YASKAWA representative about occurrence status (operating
procedure).

4000

Execution of the motion command
does not complete within the
specified time. (The last three
digits expresses the command
code.)

Software operation error
occurred

(1)Turn the power OFF then back ON.
(2)If the alarm occurs again, save the CMOS.BIN in maintenance mode, and
then contact your YASKAWA representative about occurrence status (operating
procedure).

7200

Interpolation cycle is shorter than
the set value.
(The last digit expresses the
physical axis of the alarm
occurrence.)

Software operation error
occurred

(1)Turn the power OFF then back ON.
(2)If the alarm occurs again, save the CMOS.BIN in maintenance mode, and
then contact your YASKAWA representative about occurrence status (operating
procedure).

7500

Setting error of the NSRCH
instruction direct-in

number.

Setting error

More than 4 direct in numbers are specified at time under the NSRCH
instruction. Confirm its direct-in setting value.

1200

HIGH TEMPERATURE
(IN CNTL BOX)

The temperature rises in the
controller

Turn the power OFF then back ON after cooling down inside of the controller.

Connection failure

(1)Turn the power OFF then back ON.
(2)If the alarm occurs again, check the connecting state of the following cables.
·The power cables of the cooling fan inside of the converter unit.

Module failure
(converter)

(1)Turn the power OFF then back ON.
(2)If the alarm occurs again, replace controller. Save the CMOS.BIN before
replace controller to be safe.

1204

COMMUNICATION
ERROR
(OPTION MODULE)

The communication error slot
(Serial-bus-connected Option
module communication station
No.) is displayed by the bit.
0: correct / 1: incorrect

Connection failure

Check the connecting or inserting state of the followings.
·Option modules of the corresponding slot.
·Option module cables of the corresponding slot.

IO module failure

Replace the I/O module of the corresponding station number.

Power supply broken

Replace the 24V power supply supplied to the I/O module of the corresponding
station number.

Main CPU board broken

Save the CMOS.BIN file.
Replace the Main CPU board, and then load the saved CMOS.BIN file.

1220

LAN COMMUNICATION
PARAMETER ERROR

1

Incorrect setting of the IP address
which is used in the Ethernet
function.

Setting error

(1)Check the following settings.
·IP address setting of network in maintenance mode

Alarm
Number

Alarm Name

Sub
Code

Meaning

Cause

Remedy

150 of 348

«
...
148
149
150
151
152
...
»

Summary of Contents for MOTOMAN FS100





























































































































































































































































































































































Reviews:

No comments

Related manuals for MOTOMAN FS100

Brand: Parasound Pages: 72

Brand: Jafar Pages: 15

Brand: ZETRON Pages: 3

Brand: ADEMCO Pages: 2

EtherNetIP ControlPlex CPC12EN

Brand: E-T-A Pages: 28

Brand: Hach Pages: 36

Brand: Hach Pages: 72

Brand: V2 ELETTRONICA Pages: 72

Brand: Paradox Pages: 32

Brand: Dantherm Pages: 20

PDS CONTROL Series

Brand: S&P Pages: 32

Brand: Danfoss Pages: 2

Brand: FrSky Pages: 2

Brand: Festo Pages: 62

Expedition Double Jogger

Brand: BABYTREND Pages: 18

Brand: Westfalia Pages: 18

Brand: schmersal Pages: 6

Brand: IMG STAGELINE Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands