manualshive.com logo in svg

YASKAWA MOTOMAN FS100, Maintenance Manual

The YASKAWA MOTOMAN FS100 is a state-of-the-art robotic system designed to optimize industrial manufacturing processes. Enhance your productivity by downloading the comprehensive Instructions Manual for this product, available for free download exclusively at our website.

Share
Download
background image

9-74

1596

45-1

C

D

RE-CHO-A1

11

FS10

0

16

PSTART instruction is the old 
specification.

Setting error

(1)Check the following settings.
·The specifications of PSTART instruction
Register the PSTART instruction as new specification.

17

PWAIT instruction is the old 
specification.

Setting error

(1)Check the following settings.
·The specifications of PWAIT instruction
Register the PWAIT instruction as new specification.

4104

WRONG EXECUTION 
OF LOAD INST

Sub Code1 to 245: Signifies the 
data transmission error.

Setting error

* Refer to the instruction manual for Data Transmission Function for details.

4105

WRONG EXECUTION 
OF SAVE INST

Sub Code1 to 245: Signifies the 
data transmission error.

Setting error

* Refer to the instruction manual for Data Transmission Function for details.

4106

WRONG EXECUTION 
OF DELETE INST

Sub Code1 to 245: Signifies the 
data transmission error.

Setting error

* Refer to the instruction manual for Data Transmission Function for details.

4107

OUT OF RANGE 
(ABSO DATA)

Sub Code: Signifies the axis in 
which the alarm occurred

Setting error

(1)Check the following settings.
·Move the manipulator or station to the zero position by the axis operation and 
check the home position alignment marks (the arrow).

4112

DATA SENDING ERROR

1

Retry over of NAK

Communication error

(1)Reset the alarm.
(2)If the alarm occurs again, check the communication setting and 
communication wiring is correct.

2

Retry over for timeout in timer A

Communication error

(1)Reset the alarm.
(2)If the alarm occurs again, check the communication setting and 
communication wiring is correct.

3

Retry over for mutual response 
error

Communication error

(1)Reset the alarm.
(2)If the alarm occurs again, check the communication setting and 
communication wiring is correct.

4113

DATA RECEIVING 
ERROR

1

Reception timeout (timer A)

Communication error

(1)Reset the alarm.
(2)If the alarm occurs again, check the communication setting and 
communication wiring is correct.

2

Reception timeout (timer B)

Communication error

(1)Reset the alarm.
(2)If the alarm occurs again, check the communication setting and 
communication wiring is correct.

3

Heading length is too short.

Setting error

(1)Reset the alarm.
(2)If the alarm occurs again, send EOT code to release the data link and then 
check that the sending side data is correctly set. 
(3)Check that the communication setting is correct.

Alarm
Number

Alarm Name

Sub
Code

Meaning

Cause

Remedy

176 of 348

Summary of Contents for MOTOMAN FS100





























































































































































































































































































































































Reviews:

No comments

Related manuals for MOTOMAN FS100

Hanna Instruments BL120 Instruction Manual preview
BL120
Brand: Hanna Instruments Pages: 54
Hanna Instruments BL 983320-0 Instruction Manual preview
BL 983320-0
Brand: Hanna Instruments Pages: 2
IBC MVE2 Series Quick Start Manual preview
MVE2 Series
Brand: IBC Pages: 8
Tylo 2900 5208 Installation Manual And Quick Start Manual preview
2900 5208
Brand: Tylo Pages: 51
M-system R5-TS Instruction Manual preview
R5-TS
Brand: M-system Pages: 3
Sven GC-400 Operation Manual preview
GC-400
Brand: Sven Pages: 6
CH Byron Home easy HE-440 Installation Instructions preview
Home easy HE-440
Brand: CH Byron Pages: 2
RTI T3x Quick Reference Manual preview
T3x
Brand: RTI Pages: 2
Nautronic NAUCON-40 User Manual preview
NAUCON-40
Brand: Nautronic Pages: 6
Redbusbar CircuitSpy 80 Installation And Operation Manual preview
CircuitSpy 80
Brand: Redbusbar Pages: 12
EGG QUAIL Instruction Manual preview
QUAIL
Brand: EGG Pages: 13
Mita WP3000 Manual preview
WP3000
Brand: Mita Pages: 7
Sorel TDC 5 Installation And Operating Instructions Manual preview
TDC 5
Brand: Sorel Pages: 56
Genius BRAIN 06 24V Manual preview
BRAIN 06 24V
Brand: Genius Pages: 52
Meilhaus Electronic USB-GT Manual preview
USB-GT
Brand: Meilhaus Electronic Pages: 19
Bardiani Valvole BBWO1 Instruction, Use And Maintenance Manual preview
BBWO1
Brand: Bardiani Valvole Pages: 65
Hanyoung TH500 Manual preview
TH500
Brand: Hanyoung Pages: 99
Ohio Medical Push-To-Set PTS-CVR Service Manual preview
Push-To-Set PTS-CVR
Brand: Ohio Medical Pages: 25

Brands by name

Popular brands

Load more brands