manualshive.com logo in svg

Xilinx Versal ACAP CPM4, Product Manual

Share
Download
Xilinx Versal ACAP CPM4 Product Manual Download Page 75

Table 23: Sideband Signals in pcie(n)_m_axis_cq_tuser (1024-bit Interface) (cont'd)

Bit Index

Name

Width

Description

163:160

is_sop[3:0]

4

Signals the start of a new TLP in this beat. These outputs are

set in the first beat of a TLP. When straddle is disabled, only

is_sop[0] is valid and is_sop[1] is permanently set to 0. When

straddle is enabled, the settings are as follows:

•

0000: No new TLP starting in this beat.

•

0001: A single new TLP starts in this beat. Its start

position is indicated by is_sop0_ptr[1:0].

•

0011: Two new TLPs are starting in this beat. at locations

determined by is_sop0_ptr[1:0] and is_sop1_ptr[1:0]

respectively.

•

0111: Three TLPs are starting in this beat. at locations

determined by is_sop0_ptr[1:0], is_sop1_ptr[1:0] and

is_sop2_ptr[1:0] respectively.

•

1111: Three TLPs are starting in this beat. at locations

determined by is_sop0_ptr[1:0], is_sop1_ptr[1:0],

is_sop_2_ptr[1:0] and is_sop2_ptr[1:0] respectively.

•

All other values are reserved.

Use of this signal is optional for the user logic when the

straddle option is disabled, because a new TLP always starts

in the beat following tlast assertion.

165:164

is_sop0_ptr[1:0]

2

Location of first SOP in the beat:

•

00: Byte lane 0

•

01: Byte lane 32

•

10: Byte lane 64

•

11: Byte lane 96

167:166

is_sop1_ptr[1:0]

2

Location of second SOP in the beat:

•

00:Reserved

•

01: Byte lane 32

•

10: Byte lane 64

•

11: Byte lane 96

169:168

is_sop2_ptr[1:0]

2

Location of third SOP in the beat:

•

00:Reserved

•

01: Reserved

•

10: Byte lane 64

•

11: Byte lane 96

171:170

is_sop3_ptr[1:0]

2

Location of fourth SOP in the beat:

•

00:Reserved

•

01: Reserved

•

10: Reserved

•

11: Byte lane 96

Chapter 3: Product Specification

PG346 (v3.3) November 16, 2022

 

www.xilinx.com

CPM Mode for PCI Express

 75

Send Feedback

Summary of Contents for Versal ACAP CPM4

































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands