manualshive.com logo in svg

Xilinx Versal ACAP CPM4, Product Manual

Share
Download
Xilinx Versal ACAP CPM4 Product Manual Download Page 247

RESET Placements

Allowed placements are shown in the table below. Placements are selected in CIPS IP
configuration GUI as part of PS PMC peripheral and I/O configuration selections.

Table 63: Allowed Reset Pin Placements

CPM5 PCIE Controller and Port

Type

RESET Pin Location Options

0: Endpoint, Switch Ports (Up/Down)

PS MIO 18 (Default)

PMC MIO 24
PMC MIO 38

1: Endpoint, Switch Ports (Up/Down)

PS MIO 19 (Default)

PS MIO 25
PS MIO 39

0: Root Port

PS MIO 0 (Default)

PS MIO 0 – 25

PMC MIO 0 – 51

1: Root Port

PS MIO 1 (Default)

PS MIO 0 – 25

PMC MIO 0 – 51

CPM5 Configuration Notes

The GTYP lane and quad ordering above typically results in lanes crossing for x4 and x2 endpoint
configurations. In this scenario Xilinx recommends physically reversing the lanes in the PCB
design board traces. This will typically result in a bow-tie in the board PCB traces between the
device and the PCIe edge connector.

Guidance for CPM5 in Specifically Identified

Engineering Sample Devices

Specifically identified engineering sample devices listed in the table below contain a CPM5 based
on an earlier CPM5 design database. Subsequent Xilinx plans will include additional lane
remapping support to further increase flexibility of CPM5 across a wide variety of use cases.

Appendix B: GT Selection and Pin Planning for CPM5

PG346 (v3.3) November 16, 2022

 

www.xilinx.com

CPM Mode for PCI Express

 247

Send Feedback

Summary of Contents for Versal ACAP CPM4

































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands