manualshive.com logo in svg

Xilinx Versal ACAP CPM4, Product Manual

Share
Download
Xilinx Versal ACAP CPM4 Product Manual Download Page 58

Table 15: Sideband Signals in pcie(n)_m_axis_cq_tuser (512-bit Interface) (cont'd)

Bit Index

Name

Width

Description

96

discontinue

1

This signal is asserted by the core in the last beat of a TLP, if

it has detected an uncorrectable error while reading the TLP

payload from its internal FIFO memory. The user application

must discard the entire TLP when such an error is signaled

by the core.
This signal is never asserted when the TLP has no payload.

It is asserted only in the last beat of the payload transfer,

that is when is_eop[0] is High.
When the straddle option is enabled, the core does not start

a second TLP if it has asserted discontinue in a beat.
When the core is configured as an Endpoint, the error is also

reported by the core to the Root Complex it is attached to,

using Advanced Error Reporting (AER).

182:119

parity

64

Odd parity for the 512-bit transmit data. Bit i provides the

odd parity computed for byte i of pcie(n)_m_axis_cq_tdata.

183

PASID TLP Valid 0

1

Indicates PASID TLP 0 is valid.

184

PASID TLP Valid 1

1

Indicates PASID TLP 1 is valid.

204:185

PASID 0

20

Indicates PASID TLP Prefix for packet0 to the user design.

224:205

PASID 1

20

Indicates PASID TLP Prefix for packet1 to the user design.

225

Execute Requested 0

1

Indicates Execute Requested for packet0.

226

Execute Requested 1

1

Indicates Execute Requested for packet1.

227

Privileged Mode Requested 0

1

Indicates Privileged Mode Requested for packet0 to the user

design.

228

Privileged Mode Requested 1

1

Indicates Privileged Mode Requested for packet1 to the user

design.

Completer Completion Interface

Table 16: Completer Completion Interface Port Descriptions (512-bit Interface)

Name

I/O

Width

Description

pcie0_s_axis_cc_tdata

pcie1_s_axis_cc_tdata

I

512

Completion data from the user application to the PCIe core.

pcie0_s_axis_cc_tuser

pcie1_s_axis_cc_tuser

I

81

This is a set of signals containing sideband information for

the TLP being transferred. These signals are valid when

pcie(n)_s_axis_cc_tvalid is High.
The individual signals in this set are described in the

following table.

pcie0_s_axis_cc_tlast

pcie1_s_axis_cc_tlast

I

1

The user application must assert this signal in the last cycle

of a packet to indicate the end of the packet. When the TLP

is transferred in a single beat, the user application must set

this bit in the first cycle of the transfer.
This input is used by the core only when the straddle option

is disabled. When the straddle option is enabled, the core

ignores the setting of this input, using instead the is_sop/

is_eop signals in the pcie(n)_s_axis_cc_tuser bus to

determine the start and end of TLPs.

Chapter 3: Product Specification

PG346 (v3.3) November 16, 2022

 

www.xilinx.com

CPM Mode for PCI Express

 58

Send Feedback

Summary of Contents for Versal ACAP CPM4

































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands