Xilinx Versal ACAP CPM4 Product Manual Download Page 122

Page: 122 / 288

Note: The

pcie0*

signals map to PCIe Controller 0 and

pcie1*

signals map to PCIe Controller 1 in the

port descriptions below.

Table 46: Configuration PASID Interface Port Descriptions

Port

I/O

Width

Description

pcie0_cfg_pasid_enable

pcie1_cfg_pasid_enable

Configuation PASID Enable: Per Function PASID

Enable.

pcie0_cfg_pasid_exec_permission_enable

pcie1_cfg_pasid_exec_permission_enable

Configuation PASID Exec Permission Enable: Per

Function PASID Exec Permission Enable.

pcie0_cfg_pasid_privil_mode_enable

pcie1_cfg_pasid_privil_mode_enable

Configuation PASID Privil Mode Enable: Per Function

PASID Privil Mode Enable.

Register Space

The configuration space is a register space defined by the PCI Express Base Specification 4.0
(

https://www.pcisig.com/specifications

). The Versal

ACAP CPM Mode for PCIe supports Xilinx

proprietary read/write configuration interfaces into this register space, and supports up to four
Physical Functions (PFs) and 252 Virtual Functions (VFs).

The PCI configuration space consists of the following primary parts.

Legacy PCI v4.0 Type 0/1 Configuration Space Header

• Type 0 Configuration Space Header supported for Endpoint configuration

• Type 1 Configuration Space Header supported for Root, Switch Port configuration

Legacy Extended Capability Items

• PCIe Capability

• Power Management Capability

• Message Signaled Interrupt (MSI) Capability

• MSI-X Capability

• Legacy Extend Capabilities

PCIe Extended Capabilities

• Advanced Error Reporting Capability

• Function Level Reset

• ASPM L1 Support (ASPM support for endpoint port types only; ASPM is not supported for

other port types).

Chapter 3: Product Specification

PG346 (v3.3) November 16, 2022

www.xilinx.com

CPM Mode for PCI Express

122

Send Feedback

Summary of Contents for Versal ACAP CPM4

































































































































































































































































































Search results

Summary of Contents for Versal ACAP CPM4

Reviews:

Brands by name

Popular brands

Xilinx Versal ACAP CPM4, Product Manual

Search results

Summary of Contents for Versal ACAP CPM4

Reviews:

Brands by name

Popular brands