Vertical SBX IP 320 Features & Operation Manual Download | Manualshive

Page: 31 / 248

background image

Call Handling

21

SBX IP 320 Features & Operation Guide

Conditions

•

Can be used on DKTUs and SLTs.

•

This feature is available on a per-use basis only. While activating walking COS,
hanging-up or pressing the [TRANS/PGM] button to hold the call and seize another line,
the original programmed Station COS will be used.

•

When a wrong number is dialed, press the [FLASH] button to dial again without
changing to an idle CO line.

•

The fee for a call with Walking COS will be charged according to the Station
authorization code, not the actual Station.

•

When a User tries to use Walking COS at a station set to COS 7 with temporary COS, the
call will follow the original COS of the Station.

Admin Programming

•

Authorization Code Table (PGM 227)

Call Handling

Absent Text Message

Custom Message

Each station can select from ten (11-20) available custom messages to display on the DKTU
LCD. These messages are programmed by the System Attendant for System-wide use.
Individual users may program message 00 as their own custom message.

When set, the selected message is displayed on the User Station LCD panel.

Operation

To program Custom Message 00 from a station:

1.

Press the [TRANS/PGM] button.

2.

Dial 52.

3.

Enter the message, up to 24 characters.

«
...
29
30
31
32
33
...
»

Summary of Contents for SBX IP 320

























































































































































































































































Reviews:

No comments

Related manuals for SBX IP 320

Brand: Octopus Pages: 122

Brand: Panasonic Pages: 252

Brand: Panasonic Pages: 8

Brand: Panasonic Pages: 8

Brand: Karel Pages: 43

Brand: Jabra Pages: 7

CRUISER2 HSF002

Brand: Jabra Pages: 2

XDECT 8315 Series

Brand: Uniden Pages: 44

Brand: invotel Pages: 6

Brand: AT&T Pages: 12

Brand: GE Pages: 84

DECT 1730 Series

Brand: Uniden Pages: 32

T42S-Skype for Business

Brand: Yealink Pages: 8

Brand: Fortinet Pages: 271

Brand: Skil Pages: 10

POLYCOM SOUNDSTATION IP 6000

Brand: Armstrong Pages: 2

Brand: VTech Pages: 16

Brand: Geemarc Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands