manualshive.com logo in svg

Vertical SBX IP 320, Features & Operation Manual

Introducing the Vertical SBX IP 320 system - a comprehensive business communication solution. Enhance your productivity with its advanced features and user-friendly interface. Access the Quick Reference Manual online for free, providing detailed instructions at your fingertips. Download and unlock the full potential of this exceptional product from manualshive.com.

Share
Download
background image

Hunt Groups

85

SBX IP 320 Features & Operation Guide

Operation

VMIB Announcement

The VMIB announcements can be assigned to provide different messages to each ACD group. 
The system ACD groups can be programmed to provide announcements to incoming calls to a 
group where all station are busy. Both primary and secondary announcements will be available 
and a guaranteed announcement may be assigned.

Agents

The following features are available to agents in an ACD group.

Agent Login/Logout - It is assigned by the Admin Program. An ACD agent can be assigned to 
more than one ACD group.

Agent On/Off Duty - Agent can be On/Off duty by dialing the ACD DND Code 
([TRANS/PGM] + 87 + Hunt Group Number) on the dial pad or by pressing the 
pre-programmed flexible button.

Alternate ACD Group

An alternate ACD group can be programmed so that if stations are busy, the alternate will be 
checked for an available station.

Overflow Station Assignment

An overflow station may be assigned to route callers in queue to a designated station after a 
specified time. The overflow station may not be one of the ACD group stations. The overflow 
station can be forwarded, if enabled in Admin programming.

Display Queued Calls 

LCD Display Queued call count.

LED Indication

The DSS LED of the {ACD Group} will flash at a greater frequency as the number of queued 
calls increases.

   0 : Off,  01-3 : 60 IPM,  4-6 : 120 IPM,  more than 7 : 240 IPM 

Supervisor

Supervisor Login/Logout - It is assigned by Admin Programming. Each ACD group can be 
assigned a separate supervisor.

Q U E   G r o u p   N O  ( Q u e u e  c o u n t )

Summary of Contents for SBX IP 320

























































































































































































































































Reviews:

No comments

Related manuals for SBX IP 320

Xblue Networks PCS digital User Manual preview
PCS digital
Brand: Xblue Networks Pages: 32
VTech ia5847 Errata Sheet preview
ia5847
Brand: VTech Pages: 1
GE 28128xx3 User Manual preview
28128xx3
Brand: GE Pages: 68
Uniden DXAI7288-2 Guide Utilisateur preview
DXAI7288-2
Brand: Uniden Pages: 68
Uniden DCX750 - DCX 750 Cordless Extension Handset Manual D'Utilisation preview
DCX750 - DCX 750 Cordless Extension Handset
Brand: Uniden Pages: 20
Ryobi CDD-1202 User Manual preview
CDD-1202
Brand: Ryobi Pages: 107
Inter-Tel INT2000 User Manual preview
INT2000
Brand: Inter-Tel Pages: 48
Atos Unity OpenStage M3 Ex Safety Notes preview
Unity OpenStage M3 Ex
Brand: Atos Pages: 104
Swissvoice Avena 748 User Manual preview
Avena 748
Brand: Swissvoice Pages: 20
Daewoo International DTC-760 User Manual preview
DTC-760
Brand: Daewoo International Pages: 26
Craftsman 973.225400 Operator'S Manual preview
973.225400
Brand: Craftsman Pages: 18
Siemens euroset User Manual preview
euroset
Brand: Siemens Pages: 42
US Robotics USR9600 Installation Manual preview
USR9600
Brand: US Robotics Pages: 104
Alcatel T76 User Manual preview
T76
Brand: Alcatel Pages: 4
Alcatel T37 User Manual preview
T37
Brand: Alcatel Pages: 2
Alcatel temporis 500 User Manual preview
temporis 500
Brand: Alcatel Pages: 40
Alcatel SMARTFLIP User Manual preview
SMARTFLIP
Brand: Alcatel Pages: 75
Alcatel OmniPCX 4400 User Manual preview
OmniPCX 4400
Brand: Alcatel Pages: 1

Brands by name

Popular brands

Load more brands