Vertical SBX IP 320 Features & Operation Manual Download | Manualshive

Page: 229 / 248

background image

Voice Service

219

SBX IP 320 Features & Operation Guide

3.

Pressing the [CONF] button, the current message is deleted and the next message is
heard.

•

For SLT and 2/8 BTN DKTU, Dial # 1, and press the [HOLD/SAVE] button;
the current message is saved and the next message is heard.

•

For SLT and 2/8 BTN DKTU, dial # 2, and press the [CALLBK] button, the
current message is played again.

•

For SLT and 2/8 BTN DKTU, dial # 3.

4.

Pressing the [ADD] soft button, you can record an additional message (possible with
7224D which has 3 soft keys).

5.

Pressing the [REWIND] soft button, you can rewind the current message with VM MSG
Rewind Timer (possible with 7224D which has 3 soft keys).

Conditions

•

There is no time limit to record user greeting in a station.

•

When a caller leaves a voice message wait, the recording time is controlled by Valid User
Message Timer (PGM 181 - FLEX 4) and VMIB User Record Timer (PGM 181 - FLEX
3). When the recorded message is shorter than the Valid User Message time, the message
is not saved. Also, if the User Record Timer expires, a confirmation tone is heard and the
message is saved in the station.

•

If the station has several messages to be retrieved by pressing the [CALLBK] button, the
message only with station number will be retrieved first. (Message wait with station
number -> VMIB Message wait -> CLI Message wait -> VM group Message wait)

•

Pressing the [CALLBK] button at the calling station before the user greeting is played
causes the message wait with only station number to be saved in the called station.

•

When a user calls a station which is forwarded to VMIB, they will hear the user greeting
and a beep tone. After the beep tone, the user can leave a voice message.

•

Each station may have up to 800 VMIB message waits.

•

If all the VMIB ports are busy, ring-back tone will be provided instead of the user
greeting. Also, the VMIB Station Forward Timer is started to retry to answer.

•

A User can leave and receive message wait using an SLT with message wait lamp.

•

Individual user greetings and VMIB message waits are protected from system reset.

•

To retrieve left message wait, the order of playing is changeable. Originally, TIME,
DATE, and a left message are played. Depending on how ADMIN is set, DATE, TIME,
and a left message are played.

«
...
227
228
229
230
231
...
»

Summary of Contents for SBX IP 320

























































































































































































































































Reviews:

No comments

Related manuals for SBX IP 320

Brand: BT Pages: 2

Brand: HIKOKI Pages: 112

Brand: Uniden Pages: 6

Brand: Matosio Pages: 37

Brand: GE Pages: 40

Brand: VTech Pages: 2

Brand: Alcate Pages: 17

Brand: AT&T Pages: 69

Amplidect 295 SOS-Pro

Brand: Geemarc Pages: 2

Brand: Geemarc Pages: 31

Brand: Geemarc Pages: 58

MD 491R - 174; 2.4GHz CORDED/CORDLESS PHONE SYSTEM

Brand: Motorola Pages: 64

Brand: Motorola Pages: 22

Brand: Motorola Pages: 42

Brand: Motorola Pages: 68

Brand: Motorola Pages: 21

Brand: Motorola Pages: 64

Brand: Motorola Pages: 73

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands