Vertical SBX IP 320 Features & Operation Manual Download Page 228

Page: 228 / 248

Voice Service

218

SBX IP 320 Features & Operation Guide

Dial #; then start recording after hearing the announcement "Record your message" and a
confirmation tone.

Press the [HOLD/SAVE] button.

-or-

Press the [SPEAKER] button to finish the recording; a confirmation tone sounds.

To delete a user greeting at a station:

Press the [TRANS/PGM] button.

Dial 66.

The User greeting is deleted and Forward is deactivated.

To activate call forward to VMIB from a station:

Go off-hook or press the [SPEAKER] button.

Press the [DND/FOR] button.

Dial the forward type (1-4).

Dial the # key; a confirmation tone is heard.

To deactivate call forward to VMIB from a station:

Press the [DND/FOR] button.

To leave a voice message wait at a Station:

The caller will hear the User greeting and the "Record your message" announcement.

After a beep tone, record your message.

Hang-up to complete recording.

To retrieve a recorded voice message wait at the Station:

Press the flashing [CALLBK] button; for SLT and 2/8 BTN DKTU, dial 557.

The message number prompt is heard and the voice message (FIFO or LIFO) and Time &
Date prompt for the message is played.

Summary of Contents for SBX IP 320

























































































































































































































































Search results

Summary of Contents for SBX IP 320

Reviews:

Related manuals for SBX IP 320

Brands by name

Popular brands

Vertical SBX IP 320, Features & Operation Manual

Search results

Summary of Contents for SBX IP 320

Reviews:

Related manuals for SBX IP 320

Brands by name

Popular brands