Vertical SBX IP 320 Features & Operation Manual Download Page 34 | Manualshive

Page: 34 / 248

background image

Call Handling

24

SBX IP 320 Features & Operation Guide

To cancel LCD Messages (Custom/Pre-selected) from a Station:

1.

Press the flashing [DND/FOR] button

-or-

Press the [TRANS/PGM] button.

2.

Dial 51 and the desired number.

3.

Press the [HOLD/SAVE] button.

Conditions

•

If a station assigns call forward while a pre-selected message is activated, the
pre-selected message is canceled automatically).

•

Users can leave a message at a DKTU or SLT. When leaving a message at the SLT, a
DND warning tone will sound when the handset is lifted as a reminder of the message
waiting.

•

When a pre-selected message is selected in a DKTU, the [DND/FOR] button will flash.

Admin Programming

•

Refer to the SBX IP 320 Installation Manual, Numbering Plan (PGM 106)

Alarm

The system can be programmed to recognize the status of an external contact from a relay (open
or closed). When activated, the System will signal programmed Stations with a single tone
repeated per 1-min. interval or a continuous tone. This capability is commonly employed to
provide remote alarm signals. When used as an alarm, the assigned Stations receive the
programmed signal. To stop the signal, the alarm should be deactivated (reset) from a Station
assigned to receive the alarm signal.

Operation

Upon detecting the Alarm contact, the system sends the appropriate alarm signal to assigned
stations.

To terminate the alarm signal while the line is in an idle state:

1.

Dial 565; a confirmation tone sounds.

2.

The alarm signal will be terminated at all assigned stations.

«
...
32
33
34
35
36
...
»

Summary of Contents for SBX IP 320

























































































































































































































































Reviews:

No comments

Related manuals for SBX IP 320

Brand: Panasonic Pages: 30

Brand: Panasonic Pages: 18

Brand: Gamma Pages: 20

Brand: Unify Pages: 144

Brand: UniData Communication Systems Pages: 60

Brand: Panasonic Pages: 8

Brand: Panasonic Pages: 10

Brand: Panasonic Pages: 56

Brand: Firstcom Pages: 37

Brand: Audiovox Pages: 40

Brand: Gigaset Pages: 27

Brand: AT&T Pages: 4

Brand: BT Pages: 12

Brand: Uniden Pages: 1

Brand: Aastra Pages: 36

BRAVO CORDLESS 2

Brand: BRONDI Pages: 72

Brand: Geemarc Pages: 72

Ascotel Office 35

Brand: ASCOM Pages: 68

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands