Vertical SBX IP 320 Features & Operation Manual Download Page 168

Page: 168 / 248

Paging

158

SBX IP 320 Features & Operation Guide

Conditions

•

When external paging is required, appropriate external equipment should be attached to
the proper external page connections on the MBU.

•

A station which is in DND or busy cannot receive a page.

•

A station which is not allowed to page cannot make a page.

•

When paging is used in the system, another page is not allowed at the same time.

•

A Page warning tone may be controlled by Admin. Programming.

•

When the page timer expires, the paging connection is automatically released and ICM
busy tone is presented to the paging station.

•

You should lift the handset to make a page. When trying to make a page without lifting
handset, "LIFT HANDSET TO PAGE" displays on the LCD.

•

Paging can be programmed to a Flex. button.

•

If an intercom call is received to the paging station, the caller will hear an intercom busy
tone.

•

If a CO line call is received at the paging station, the station will receive off-hook ring.

•

A station may respond to a meet me page regardless of assignment of pick-up/paging
group assignment/page access.

•

A Page from a CO line can't be answered by pressing the [HOLD/SAVE] button or the
code for meet-me answer. If a user tries to answer a meet me page request from CO line,
an error tone is heard and an LCD message for error will be displayed.

Admin Programming

•

Paging Timeout Timer (PGM 181 - FLEX 10)

•

Page Warning Tone (PGM 161 - FLEX 4)

•

Page Access (PGM 111 - FLEX 8)

•

Internal Page Zone (PGM 118)

•

External Control Contact (PGM 168)

Summary of Contents for SBX IP 320

























































































































































































































































Search results

Summary of Contents for SBX IP 320

Reviews:

Related manuals for SBX IP 320

Brands by name

Popular brands

Vertical SBX IP 320, Features & Operation Manual

Search results

Summary of Contents for SBX IP 320

Reviews:

Related manuals for SBX IP 320

Brands by name

Popular brands