Vertical SBX IP 320 Features & Operation Manual Download

Page: 157 / 248

Outgoing Call Access

147

SBX IP 320 Features & Operation Guide

•

Number of 'Dialed Code Bins': 250 bins

•

Number of 'Modification Code Bins': 100 bins

•

Maximum number of 'Dialed digits': 12 digits

•

Maximum number of 'Added digits': 25 digits

•

Alternative DMT index: 1 ea

Admin Programming

•

LCR Attributes (PGM 220)

•

Leading Digit Table (PGM 221)

•

Digit Modification Table (PGM 222)

•

LCR Table Initialization (PGM 223)

Memory Dialing

Auto Call Number Redial (ANCR)

If Call destination is busy or no answer, redialing is operated repeatedly within the ACNR retry
counter. The system will retry the number based on programming with appropriate pauses in
between dialing (default = 3 times).

Operation

To use ACNR while receiving a busy/no answer indication on a CO Line, use the following
procedure:

Press the [REDIAL] button.

Replace the handset or go on-hook.

The system will automatically retry the call at programmed intervals.

When the called party answers, lift handset.

-or-

Press the [MUTE] button to make the call.

Summary of Contents for SBX IP 320

























































































































































































































































Search results

Summary of Contents for SBX IP 320

Reviews:

Related manuals for SBX IP 320

Brands by name

Popular brands

Vertical SBX IP 320, Features & Operation Manual

Search results

Summary of Contents for SBX IP 320

Reviews:

Related manuals for SBX IP 320

Brands by name

Popular brands