Vertical SBX IP 320 Features & Operation Manual Download Page 69

Page: 69 / 248

Call Handling

SBX IP 320 Features & Operation Guide

•

To assign the {Mobile Extension Activation} button:

[TRANS/PGM] + {FLEX} + [TRANS/PGM] + 34 + [HOLD/SAVE]

•

If the extension is a member of a Hunt Group (except Ring Hunt Group), a call is routed
to the mobile extension.

•

To use the mobile extension in case of Hunt group member, Hunt call should be
programmed in PGM 236, FLEX 5.

•

A mobile extension can transfer a call to another station's mobile extension.

Admin Programming

•

Mobile Extension Register (PGM 236)

Music On Hold (MOH)

When a CO call is placed on hold, the external party will hear music.

MOH is supplied through various music sources. Music can be played to any party on hold. The
following music sources are available:

•

Internal Music

•

External Music

•

SLT MOH

Operation

The following values are associated with MOH:

0 = Not assigned

1 = Internal Music

2 = External Music

3 = Reserved

9 = Hold Tone

Conditions

•

Only 1 MOH channel is supported.

•

SLT ports connected with MOHU can provide MOH channels.

Summary of Contents for SBX IP 320

























































































































































































































































Search results

Summary of Contents for SBX IP 320

Reviews:

Related manuals for SBX IP 320

Brands by name

Popular brands

Vertical SBX IP 320, Features & Operation Manual

Search results

Summary of Contents for SBX IP 320

Reviews:

Related manuals for SBX IP 320

Brands by name

Popular brands