Vertical SBX IP 320 Features & Operation Manual Download Page 171

Page: 171 / 248

Paging

161

SBX IP 320 Features & Operation Guide

Push-to-Talk (PTT)

Using the PTT button of the Nomad IP, the user can talk to members of an internal page zone.

Operation

To register internal page zone for PTT:

Press the [TRANS/PGM].

Press "1#".

Input the internal page zone for PTT. If want to remove the assigned page zone, input "0".

Press the [HOLD/SAVE] button.

To use PTT:

Press the PTT button of the Nomad IP.

The user can talk to members of the internal page zone assigned.

If the PTT button is released, paging is ended.

Conditions

•

PTT follows the feature operation of internal call page, except the Page Timer isn't
applied.

•

The range of internal page zone for PTT follows the internal page zone of each system
except conference page zone.

Summary of Contents for SBX IP 320

























































































































































































































































Search results

Summary of Contents for SBX IP 320

Reviews:

Related manuals for SBX IP 320

Brands by name

Popular brands

Vertical SBX IP 320, Features & Operation Manual

Search results

Summary of Contents for SBX IP 320

Reviews:

Related manuals for SBX IP 320

Brands by name

Popular brands