Vertical SBX IP 320 Features & Operation Manual Download Page 208

Page: 208 / 248

Supplementary Service

198

SBX IP 320 Features & Operation Guide

Message Wait Notification to Mobile Extension

When a VMIB message has been left at a station, the system can send a message wait
notification to a mobile phone linked with the station.

Operation

To activate (deactivate) message wait notification to a mobile phone:

Press [PGM] + 36.

Dial "1" to activate ("0" to deactivate).

Press the [HOLD] button.

Condition

•

This can be activated when the SMS admin PGM turns on.

Admin Programming

•

PGM 291 - FLEX 1 - SMS Service Center Number

•

PGM 291 - FLEX 2 - SMS CENTER CLI

•

PGM 292 - FLEX 1 - SMS Receive Station Assignment

•

PGM 292 - FLEX 3 - SMS Usage

•

PGM 292 - FLEX 4 - SMS Outgoing CO (CO to use for SMS sending)

•

PGM236 - Mobile Extension

Summary of Contents for SBX IP 320

























































































































































































































































Search results

Summary of Contents for SBX IP 320

Reviews:

Related manuals for SBX IP 320

Brands by name

Popular brands

Vertical SBX IP 320, Features & Operation Manual

Search results

Summary of Contents for SBX IP 320

Reviews:

Related manuals for SBX IP 320

Brands by name

Popular brands