Vertical SBX IP 320 Features & Operation Manual Download | Manualshive

Page: 66 / 248

background image

Call Handling

56

SBX IP 320 Features & Operation Guide

Message Wait Indication (MWI) - SLT Feature

If the SLT station receives a message from another User, then the SLT LED will flash indicating
a message is waiting.

Conditions

•

When lifting handset, user will hear a DND warning tone indicating message waiting.

•

When a message waiting indication prompt is recorded in the System greeting 097, a
voice announcement will be heard instead of the DND warning tone.

Admin Programming

•

Station ID Assignment (PGM 110 - FLEX 1)

Mobile Extension

A mobile user is able to use the phone as an extension of the SBX IP 320 system to receive
incoming and make outgoing calls when the mobile phone number is registered to the SBX IP
320 System.

Operation

To register a mobile extension number to a DKTU.

1.

Press the [TRANS/PGM] button.

2.

Dial 33.

3.

Dial the mobile phone number that is being registered.

4.

Press the [HOLD/SAVE] button.

To activate (deactivate) a mobile extension, use the following procedure:

1.

Press the [TRANS/PGM] button.

2.

Dial 34.

3.

Dial 1 to activate the extension, or 0 to deactivate it.

4.

Press the [HOLD/SAVE] button.

«
...
64
65
66
67
68
...
»

Summary of Contents for SBX IP 320

























































































































































































































































Reviews:

No comments

Related manuals for SBX IP 320

Brand: Felisatti Pages: 120

Brand: Panasonic Pages: 24

Brand: GE Pages: 62

JX20 - Pura - Headset

Brand: Jabra Pages: 4

Brand: GE Pages: 46

Brand: BT Pages: 69

Brand: Uniden Pages: 54

Brand: Clas Ohlson Pages: 2

Brand: Uniden Pages: 72

DECT 6.0 LS6315 Series

Brand: VTech Pages: 36

Mobile Speakerphone P710e

Brand: Logitech Pages: 7

Brand: Alcatel Pages: 74

Brand: Hitachi Pages: 96

Brand: Hitachi Pages: 29

Brand: Hitachi Pages: 27

Brand: Blueant Pages: 60

Brand: Linksys Pages: 2

gigaset classic 4000

Brand: Siemens Pages: 23

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands