background image

Conference

77

SBX IP 320 Features & Operation Guide

To Transfer CO Call to conference room:

1.

Press the [TRANS/PGM] button at the Attendant Station.

2.

Dial the activated Conference Room Number (571-579).

3.

Dial the password for entering the conference room (optional).

To check Conference Room status from the Attendant Station:

1.

At the Attendant Station, dial a conference room status code [TRANS/PGM] + dial 0 + 4 
+ 7.

2.

Enter conference room number (1-9) to monitor.

3.

The Attendant LCD will show the number of members joining the conference room.

To delete room forcedly by Attendant:

1.

Dial a conference room forced delete code, [TRANS/PGM] + 048.

2.

Enter the Room number and press [HOLD/SAVE].

3.

When erasing Conference room at ATD station, password is not needed.

Conditions

The Maximum number of conference rooms is 9.

A maximum of 15 members can enter each room.

Assigning and entering a password is Optional.

CONF ROOM status can be checked by ATD (how many members are joining the 
conference room).

For CO party, only ISDN line can enter a conference room.

If system attendant has a conference room button, she can check the status of conference 
room by checking the LED indication.

- ON - The conference room is activated, but there is no members in the room.

- OFF - The conference room is deactivated.

- Flash 60 IPM - The number of members are 1 to 3.

- Flash 120 IPM - The number of members are 4 to 6.

- Flash 240 IPM - The number of members are more than 7.

In case of Analog Line which is set to a valid "Open Loop timer" (PGM 142 - FLEX 13), 
a DISA and transferred CO call can be a member of conference.

PGM 160 - FLEX 11 option is used as a Conference feature. Entering and Leaving tones 
are controlled by PGM 160 - FLEX 11.

Summary of Contents for SBX IP 320

























































































































































































































































Reviews: