Vertical SBX IP 320 Features & Operation Manual Download Page 48 | Manualshive

Page: 48 / 248

background image

Call Handling

38

SBX IP 320 Features & Operation Guide

Emergency Intrusion

If an Emergency Supervisor Station calls another station and the Supervisor receives a busy
tone, the Supervisor can dial the Emergency Intrusion code and converse directly with the called
station.

Operation

To activate Emergency Intrusion:

Dial the Emergency Intrusion code '#' while encountering a busy tone.

Conditions

•

An Emergency Intrusion call is only possible when the calling station is set to be an
Emergency Supervisor in Admin programming.

•

If the station was talking to another station or CO line, the call is disconnected when the
station receives an Emergency Intrusion call.

•

The busy station is connected to the Emergency supervisor after a short beep tone
indication.

•

An Emergency Intrusion call is not possible to a station in a DND state.

•

An Emergency Intrusion call is not possible to an Attendant.

•

An Emergency Intrusion call is not possible to a Net DSS.

•

An Emergency supervisor is connected to the Master station of a Linked pair if both the
Master and Slave are busy.

•

An Emergency supervisor is connected to the Secretary Station instead of Executive
station.

Admin Programming

•

Emergency Supervisor (PGM 112 - FLEX 24)

«
...
46
47
48
49
50
...
»

Summary of Contents for SBX IP 320

























































































































































































































































Reviews:

No comments

Related manuals for SBX IP 320

Brand: Panasonic Pages: 32

Brand: Panasonic Pages: 10

Brand: Viking Pages: 2

XDECT SSE47 Series

Brand: Uniden Pages: 44

Brand: Topeak Pages: 2

Brand: Chamberlain Pages: 4

Intenna CP-2525

Brand: Cobra Pages: 14

Brand: GE Pages: 64

Brand: Panasonic Pages: 6

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 7

Brand: Panasonic Pages: 8

Brand: Panasonic Pages: 32

Brand: Panasonic Pages: 36

Brand: Panasonic Pages: 36

Brand: Panasonic Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands