Vertical SBX IP 320 Features & Operation Manual Download Page 183 | Manualshive

Page: 183 / 248

background image

Rerouting

173

SBX IP 320 Features & Operation Guide

•

A call forwarding station cannot leave a VMIB message.

•

The call forward feature may be canceled by code 559; the unified cancel code for
DND/Call Forward/Message for SLT.

•

Dial pulse SLT cannot be forwarded to VMIB.

Admin Programming

Call Forward (PGM 111 - FLEX 2)

VMIB Access (PGM 113 - FLEX 2)

Preset Call Forward

When a station receives incoming CO Calls and the Station is programmed to Preset Call
Forward, the call is routed to the Preset Call Forward destination if the station does not answer
within the Preset Call Forward Timer.

The destination can be another Station or a Hunt Group.

Conditions

•

In Preset Call Forward, a busy station will not receive a CO Line ring and the next
assigned station will receive the CO Line ring. If the station is not forwarded to another
destination, then the call will not be forwarded and will continue to ring at the station
until answered.

•

The Preset Call Forward loop feature is not available (A>B>C>A).

•

When a CO Line is forwarded with Preset Call Forward, the original station will stop
ringing (the LED of {CO} button will flash continuously).

•

If there is no direct {CO} button or {LOOP} button at destination station, the station will
be bypassed.

Admin Programming

•

Preset Call Forward (PGM 121)

•

Preset Call Forward Timer (PGM 181 - FLEX 12)

«
...
181
182
183
184
185
...
»

Summary of Contents for SBX IP 320

























































































































































































































































Reviews:

No comments

Related manuals for SBX IP 320

Brand: Panasonic Pages: 1182

Brand: 2N Pages: 21

Brand: 2N Pages: 59

Brand: AT&T Pages: 33

Brand: GE Pages: 84

Brand: Rath Pages: 9

Brand: Linksys Pages: 6

myPhone Jazz 202112

Brand: mPTech Pages: 65

Brand: Plantronics Pages: 2

Brand: Wesco Pages: 32

Unity OpenStage M3 Ex

Brand: Atos Pages: 104

DXI8560-2 - DXI Cordless Phone

Brand: Uniden Pages: 20

Brand: Chronos Telecom Pages: 38

Brand: D-Link Pages: 59

Brand: D-Link Pages: 67

Brand: D-Link Pages: 8

Brand: NEC Pages: 18

Brand: Nokia Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands