Unipulse F156 Operation Manual Download Page 88

Page: 88 / 160

6.FUNCTIONS

6-12-6. Over/under comparison / Upper/lower limit comparison 1 /

Near zero comparison

For each comparing point such as final, the comparing weight (gross or net) and timing can be

selected.

The following three items are selectable.

1) Over/under comparison

Select the weight value for Over/under comparison. (Code No 20)

Over/under comparison weight value /
2 : Comparison OFF 1 : Net weight 0 : Gross weight

2) Upper/lower limit comparison 1

Select the weight value for upper/lower limit comparison. (Code No 21)

Upper/lower limit comparison weight value /
2 : Comparison OFF 1 : Net weight 0 : Gross weight

3) Near zero comparison

Select the weight value for near zero comparison. (Code No 22)

Near zero comparison weight value /
2 : ComparisonOFF 1 : Net weight 0 : Gross weight

Summary of Contents for F156

































































































































































Search results

Summary of Contents for F156

Reviews:

Related manuals for F156

Brands by name

Popular brands

Unipulse F156, Operation Manual

Search results

Summary of Contents for F156

Reviews:

Related manuals for F156

Brands by name

Popular brands