Toyota Lexus IS300 Manual Download Page 43 | Manualshive

Page: 43 / 389

background image

SWITCHES

30

HEADLIGHT DIMMER AND TURN

SIGNAL SWITCH

SV12010

For high beam, push the lever forward. Pull it back for low
beam. For the headlight flasher, pull it further back.

A blue light in the instrument cluster indicates high beam or
headlight flasher is on.

The headlight flasher works even when the headlight switch is
off.

SV12011

For signaling turns, move the lever up or down in the
conventional manner.

The ignition key must be in the ”ON” position.

The turn signal is self–cancelling after a turn, but after a lane
change, you may have to cancel it by hand. You can also signal
a lane change by moving the turn signal lever partway and
holding it there.

If the green light in the instrument cluster flashes faster than
normal, it indicates that the front or rear turn signal bulb has
burned out. If this indicator light does not come on, the fuse
or the indicator light itself has probably failed.

2003 IS300 from Aug. ’02 Prod. (OM53439U)

«
...
41
42
43
44
45
...
»

Summary of Contents for Lexus IS300






































































































































































































































































































































































































Reviews:

No comments

Related manuals for Lexus IS300

Brand: ABL Pages: 176

Brand: ABL Pages: 94

Brand: Vauxhall Pages: 2

Brand: Vauxhall Pages: 2

Brand: Vauxhall Pages: 2

Brand: Vauxhall Pages: 209

Brand: VBC Racing Pages: 34

2013 Corsa Infotainment system

Brand: Vauxhall Pages: 2

Brand: Vauxhall Pages: 2

Brand: Vauxhall Pages: 236

Brand: Toyota Pages: 165

Brand: Xpresskit Pages: 18

Brand: Thule Pages: 3

Brand: Gator Pages: 6

Brand: F.lli Menabo Pages: 16

OUTLANDER PHEV 2022

Brand: Mitsubishi MOTORS Pages: 8

Brand: Renault Pages: 11

transit connect 2012

Brand: Ford Pages: 299

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands