Toyota Lexus IS300 Manual Download Page 288 | Manualshive

Page: 288 / 389

background image

IN CASE OF AN EMERGENCY

275

SV41034

When closing the board, replace the hook also in its
original position as shown.

NOTICE

If you close the back door with the board hooked, the
hook may be damaged.

Spare tire with turning direction indicators
(Some models)

SV41014

The spare tire with turning direction indicators is of a
uni–directional type and is intended for use on the
passenger side of the vehicle.

Installing the wheel on the driver side of the vehicle will not
affect tire performance. If the spare tire is used on the driver
side of the vehicle, it should be used only temporarily and then
replaced with the correct one.

2003 IS300 from Aug. ’02 Prod. (OM53439U)

«
...
286
287
288
289
290
...
»

Summary of Contents for Lexus IS300






































































































































































































































































































































































































Reviews:

No comments

Related manuals for Lexus IS300

GRAND CHEROKEE 2023

Brand: Jeep Pages: 108

Yamaha Rhino 660

Brand: Yamaha Pages: 3

Brand: Metra Electronics Pages: 12

Brand: Halfords Pages: 4

Brand: Whispbar Pages: 15

Quattroporte Automatic

Brand: Maserati Pages: 272

Brand: Whispbar Pages: 15

Brand: Hummer Pages: 502

Brand: Hyundai Pages: 280

Brand: SAN HIMA Pages: 7

Peterbilt SmartAir

Brand: Paccar Pages: 58

Brand: Mercedes-Benz Pages: 153

Brand: Kia Pages: 11

Brand: Saab Pages: 426

BASIC TLL171231

Brand: Tellur Pages: 5

Brand: Camoplast Pages: 19

ULTIMATE SPEED 296713

Brand: walser Pages: 10

Brand: Mercedes-Benz Pages: 373

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands